Search found 391 matches
- Sat Apr 20, 2024 10:00 pm
- Forum: Bug Reports
- Topic: STM32f411CE RCC / Timings
- Replies: 5
- Views: 73
Re: STM32f411CE RCC / Timings
Yes, that's correct
- Sat Apr 20, 2024 12:57 pm
- Forum: Bug Reports
- Topic: STM32f411CE RCC / Timings
- Replies: 5
- Views: 73
Re: STM32f411CE RCC / Timings
Ah, well done.
As there are a number of internal clocks, everything relates to the input clock frequency (internal, or external crystal)
So it's the input clock frequency that is limited to 26Mhz (and is set in the project options clock speed)
As there are a number of internal clocks, everything relates to the input clock frequency (internal, or external crystal)
So it's the input clock frequency that is limited to 26Mhz (and is set in the project options clock speed)
- Sat Apr 20, 2024 8:56 am
- Forum: Bug Reports
- Topic: STM32f411CE RCC / Timings
- Replies: 5
- Views: 73
Re: STM32f411CE RCC / Timings
Have you set the clock speed in project settings, to the frequency of the external crystal?
Just checking
Otherwise, could you post an example project?
Just checking
Otherwise, could you post an example project?
- Tue Apr 09, 2024 10:44 pm
- Forum: Projects - Embedded
- Topic: SPI_ Master SendByteArray only sending once in loop
- Replies: 5
- Views: 138
Re: SPI_ Master SendByteArray only sending once in loop
I think the array gets filled with the received in data.
But I can't check the component just now.
But I can't check the component just now.
- Tue Mar 26, 2024 6:26 pm
- Forum: Bug Reports
- Topic: GPS not send LAT_LONG
- Replies: 27
- Views: 453
Re: GPS not send LAT_LONG
As chipfryer27 says, I would suspect the issues are due to weak received signal strength. Time reception does not require sight of multiple satellites, position does. Can you run the setup outside, or near a window?
- Sun Mar 24, 2024 9:50 pm
- Forum: Projects - Embedded
- Topic: RS485 example
- Replies: 41
- Views: 938
Re: RS485 example
A baud rate issue?output of the Tx terminal of the pic within Proteus, activity is seen but what the virtual terminal reads does not correspond to the values that Flowcode is sending.
Is the PIC clock setup ok?
- Sat Mar 09, 2024 10:10 am
- Forum: General
- Topic: Any Pin Interrupt
- Replies: 6
- Views: 220
Re: Any Pin Interrupt
Use the Flowcode Interrupt icon
Add it once at the start of your main program.
It has properties where you set the input pin to be used, and the macro to call when the interrupt occurs.
Add it once at the start of your main program.
It has properties where you set the input pin to be used, and the macro to call when the interrupt occurs.
- Sat Feb 17, 2024 11:06 am
- Forum: Bug Reports
- Topic: STM32Fxxx wrong pins in FC10
- Replies: 2
- Views: 153
Re: STM32Fxxx wrong pins in FC10
Hi, The Flowcode STM32F development board targets have a board pin view for simplicity, e.g. for Arduino shields etc., rather than full chip view. (Table 5 for 32F746Discovery) If you need access to the full chip pins, then swap the Flowcode target from 32F446Nucleo64 to 32F446RE Unfortunately, 32F7...
- Sat Feb 10, 2024 3:40 pm
- Forum: Bug Reports
- Topic: Pi PICO No Hardware I2C on Channel 1 or Channel 2
- Replies: 14
- Views: 485
Re: Pi PICO No Hardware I2C on Channel 1 or Channel 2
Create a byte Buffer[8]
Call Transaction_Initialise (with the device address as a parameter)
Setup the Buffer data (Buffer[0] = register address, Buffer[1] = data)
Call Transaction_Write(Buffer, 2)
Call Transaction_Initialise (with the device address as a parameter)
Setup the Buffer data (Buffer[0] = register address, Buffer[1] = data)
Call Transaction_Write(Buffer, 2)
For the Pico, yesAre all other macros listed are redundant, other than any Transaction_xxx macros ?
- Sat Feb 10, 2024 1:27 pm
- Forum: Bug Reports
- Topic: Pi PICO No Hardware I2C on Channel 1 or Channel 2
- Replies: 14
- Views: 485
Re: Pi PICO No Hardware I2C on Channel 1 or Channel 2
Hi, The issue is that on Pico (and other families, such as STM32, ESP32, Raspberry Pi) the I2C does not work at the low level "Start, Byte, Stop" (as it does on PIC etc) You need to use the Transaction API that use data buffers. ps. You can also use the Transaction API with PIC, the CAL does the low...