Flowcode Support Board

I'm committed to a project using the STM32F407IG MCU, though the project wouldn't build to Hex file and I don't think I'm doing anything stupidly obvious (don't quote me on that ). I haven't encountered such issues before for other/smaller MCUs of the STM32F407... family.

I then stripped out all macros and components and merely stuck a basic loop at the start of a barebones project, but it still doesn't build.

Initialisation parameters in build options are taken directly from CubeMX (without clock issues), leading me to suspect an issue elsewhere.

I provide the basic source project and compiler report for investigation, hoping this is something simple and can be resolved quite soon.

Thanks and regards,

Brendan


Using FCD settings for compiler
Launching the compiler...
C:\ProgramData\MatrixTSL\FlowcodeV10\FCD\ARM\batch\stm32comp.bat "BUILD_ERROR_DEBUG_STM32F407IG" "C:\PROJECTS\Futura\Flowcode\" "32F407xx" "F4" "stm32f_ccm64.ld" "16000000" "1024K" "128K" "C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\"
C:\PROJECTS\Futura\Flowcode>REM CRC: 1CECFE3DB3A1BD5169AEA98AD43ADE631EF0A88FFA736FBD84BE44176323F463C8515F4CD0D20BEBDFE06A9E70103FA105C640EF477B79E0C7881D2E5EEC9BD69A0D46BD3B6AACB92DE4D84759EBB5079CA9DA2D2BBCDAE2A4D1C56CD1580BF532505B4DECBAEAC96954F191918D76F05058F85C62E78168DB2117B7F66DFFAB9D4CD39D9819A47B593E224EEC6BA2B1CF18B22880D87C51B667E8BA6E12E6B26FA06B6F4F108199331CCC4A9A2DADF899B5E4011DBDD5202C3050DA273BE4EEBA213254BC0AD6E15FDF8E24F7A49525E37122B659B22A01CA71203F3D907500295E1D946A835C79
C:\PROJECTS\Flowcode>REM REVISION: 1.0
C:\PROJECTS\Flowcode>REM GUID: E810EE73-4726-4718-B23E-B579C5ADBC40
C:\PROJECTS\Flowcode>REM DATE: 08\08\2022
C:\PROJECTS\Flowcode>REM DIR: FCD\ARM\batch\stm32comp.bat
Project BUILD_ERROR_DEBUG_STM32F407IG
Device STM32F407xx
C:\PROJECTS\Flowcode>arm-none-eabi-gcc -mcpu=cortex-m4 -mthumb -mfloat-abi=hard -mfpu=fpv4-sp-d16 -Os -DSTM32 -DSTM32F4 -DSTM32F407xx -DUSE_HAL_DRIVER -DHSE_VALUE=16000000 -I"C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\stm32cubeF4\Drivers\CMSIS\Include" -I"C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\stm32cubeF4\Drivers\CMSIS\Device\ST\STM32F4xx\Include" -I"C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\stm32cubeF4\Drivers\STM32F4xx_HAL_Driver\Inc" -I"C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\stm32cubeF4\Drivers\STM32F4xx_HAL_Driver\Inc\Legacy" -I"C:\Program Files (x86)\Flowcode\Common\Compilers\starm\\inc" -fmessage-length=0 -fdata-sections -ffunction-sections -w -c "BUILD_ERROR_DEBUG_STM32F407IG.c" -o "BUILD_ERROR_DEBUG_STM32F407IG_STM32F407xx_16000000\BUILD_ERROR_DEBUG_STM32F407IG.o"
BUILD_ERROR_DEBUG_STM32F407IG.c:74:80: error: invalid initializer
MX_GLOBAL MX_UINT32 FCV_GAUGE_MEASVALSRAW_PREV[FCVsz_GAUGE_MEASVALSRAW_PREV] = 0; // Records the previous gauge measurement values for compare to new
Error(s) in build
C:\ProgramData\MatrixTSL\FlowcodeV10\FCD\ARM\batch\stm32comp.bat reported error code 0x1
Autoclose turned off
FINISHED

Hi Brendan

I also get an error
There is a problem with these variables. I have deleted these, then I can compile it

Many thanks Stefan!

I'll revisit the vars to see if there's anything obvious with them, and a successful duplication and rebuild of the same barebones project and settings confirm what you say.

I suspect something had a hiccup somewhere along the way (e.g. accepted illegal initialiser, or something like that), and thank you again. Entirely appreciated, and a great relief!

Best regards,
Brendan

Hi Brendan

Any time again.

I think it's just this initial value of the array. Do not use a value

Thanks Stefan.

Indeed, your finding is ahead of me, and aware that arrays can only be initialised using (e.g.) syntax { 0,0,0,0 }, I'm not sure where the single '0' came from, or how that got past the gatekeeper if my own fault.

Anyway, thank you again, and lesson learned for future reference

Best regards,
Brendan