[Device]
Pins=28
Ports=5
ADCPins=14
ADCBits=10
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x2007
ConfigCount=2
PWMCount=2
EepromSize=256
HasAltPWM=0
Pwm2IsD4=0
FlowcodeProduct=PIC
UsesGpio=0
DefaultPackageType=0

[Pins]
Pin1 = "MCLR/VPP/RE3"
Pin2 = "RA0/AN0"
Pin3 = "RA1/AN1"
Pin4 = "RA2/AN2/VREF-"
Pin5 = "RA3/AN3/VREF+"
Pin6 = "RA4/T0CKI"
Pin7 = "RA5/AN4"
Pin8 = "VSS"
Pin9 = "OSC1/CLKIN/RA7"
Pin10 = "OSC2/CLKOUT/RA6"
Pin11 = "RC0/T1OSO/T1CKI"
Pin12 = "RC1/T1OSI"
Pin13 = "RC2/CCP1"
Pin14 = "RC3"
Pin15 = "RC4"
Pin16 = "RC5"
Pin17 = "RC6/TX/CK"
Pin18 = "RC7/RX/DT"
Pin19 = "VSS"
Pin20 = "VDD"
Pin21 = "RB0/INT/AN12"
Pin22 = "RB1/AN10"
Pin23 = "RB2/AN8"
Pin24 = "RB3/PGM/AN9"
Pin25 = "RB4/AN11"
Pin26 = "RB5/AN13"
Pin27 = "RB6/PGC"
Pin28 = "RB7/PGD"

[Ports]
PortPin1=0x0403
PortPin2=0x0000
PortPin3=0x0001
PortPin4=0x0002
PortPin5=0x0003
PortPin6=0x0004
PortPin7=0x0005
PortPin9=0x0007
PortPin10=0x0006
PortPin11=0x0200
PortPin12=0x0201
PortPin13=0x0202
PortPin14=0x0203
PortPin15=0x0204
PortPin16=0x0205
PortPin17=0x0206
PortPin18=0x0207
PortPin21=0x0100
PortPin22=0x0101
PortPin23=0x0102
PortPin24=0x0103
PortPin25=0x0104
PortPin26=0x0105
PortPin27=0x0106
PortPin28=0x0107


[PortMasks]
;Only bits 0-5 available on port A
PortMask0=0xFF
PortMask1=0xFF
PortMask2=0xFF
PortMask3=0x00
PortMask4=0x08

[ADCPins]
ADC0=2
ADC1=3
ADC2=4
ADC3=5
ADC4=7
ADC5=0
ADC6=0
ADC7=0
ADC8=23
ADC9=24
ADC10=22
ADC11=25
ADC12=21
ADC13=26

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansel = 0;\nanselh = 0;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="tris%p = tris%p | %m;\n%o = port%p;\n"
InputCmdOneBit="tris%p = tris%p | %m;\n%o = ((port%p & %m) == %m);\n"
InputCmdMask="tris%p = tris%p | %m;\n%o = port%p & %m;\n"
OutputCmdFull="tris%p = 0x00;\nport%p = %o;\n"
OutputCmdOneBit="tris%p = tris%p & %i;\nif (%o)\n\tport%p = (port%p & %i) | %m;\nelse\n\tport%p = port%p & %i;\n"
OutputCmdMask="tris%p = tris%p & %i;\nport%p = (port%p & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
ADCCapture="//set up ADC conversion\nchar old_tris, cnt;\n#define MX_ADC_SAMP_TIME 40\nadcon1 = 0x00;\n\n//find appropriate bit\n#if (%a == 0)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x01\n  ansel = 0x01;\n#endif\n#if (%a == 1)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x02\n  ansel = 0x02;\n#endif\n#if (%a == 2)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x04\n  ansel = 0x04;\n#endif\n#if (%a == 3)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x08\n  ansel = 0x08;\n#endif\n#if (%a == 4)\n  #define MX_ADC_TRIS_REG  trisa\n  #define MX_ADC_TRIS_MSK  0x20\n  ansel = 0x10;\n#endif\n#if (%a == 8)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x04\n  anselh = 0x01;\n#endif\n#if (%a == 9)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x08\n  anselh = 0x02;\n#endif\n#if (%a == 10)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x02\n  anselh = 0x04;\n#endif\n#if (%a == 11)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x10\n  anselh = 0x08;\n#endif\n#if (%a == 12)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x01\n  anselh = 0x10;\n#endif\n#if (%a == 13)\n  #define MX_ADC_TRIS_REG  trisb\n  #define MX_ADC_TRIS_MSK  0x20;\n  anselh = 0x20;\n#endif\n\n//sanity check\n#ifndef MX_ADC_TRIS_REG\n  #pragma error ADC conversion code error - please contact technical support\n#endif\n \n//store old tris value, and set the i/o pin as an input\nold_tris = MX_ADC_TRIS_REG;\nMX_ADC_TRIS_REG = MX_ADC_TRIS_REG | MX_ADC_TRIS_MSK;\n \n//turn ADC on\nadcon0 = 0x81 | (%a << 2);\n\n//wait the acquisition time\ncnt = 0;\nwhile (cnt < MX_ADC_SAMP_TIME) cnt++;\n \n//begin conversion and wait until it has finished\nadcon0 = adcon0 | 0x02;\nwhile (adcon0 & 0x02);\n\n//restore old tris value, and reset adc registers\nMX_ADC_TRIS_REG = old_tris;\nansel = 0;\nanselh = 0;\nadcon0 = 0x80;\n#undef MX_ADC_TRIS_REG\n#undef MX_ADC_TRIS_MSK\n#undef MX_ADC_SAMP_TIME\n"
ADCHigh="return adresh;\n"
ADCLow="char adclow;\nadclow = adresl;\nreturn adclow;\n"
ADCFull="short iRetVal;\niRetVal = (adresh << 2);\niRetVal += (adresl >> 6);\nreturn (iRetVal);\n"
InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P16F886
Define2=#define MX_EE
Define3=#define MX_EE_SIZE 256
Define4=#define MX_SPI
Define5=#define MX_SPI_C
Define6=#define MX_SPI_SDI 4
Define7=#define MX_SPI_SDO 5
Define8=#define MX_SPI_SCK 3
Define9=#define MX_UART
Define10=#define MX_UART_C
Define11=#define MX_UART_TX 6
Define12=#define MX_UART_RX 7
Define13=#define MX_I2C
Define14=#define MX_MI2C
Define15=#define MX_I2C_C
Define16=#define MX_I2C_SDA 4
Define17=#define MX_I2C_SCL 3
Define18=#define MX_PWM
Define19=#define MX_PWM_CNT 2
Define20=#define MX_PWM_TRIS1 trisc
Define21=#define MX_PWM_1 2
Define22=#define MX_PWM_TRIS2 trisc
Define23=#define MX_PWM_2 1

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"
GeneralInit="intcon.GIE=1;\n"
Count=3
1=TMR0
2=RB0INT
3=PORTB

[TMR0]
;it is vital that this section remains exactly as-is (for all chips?)
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=T0IF
EnReg=intcon
EnBit=T0IE
OptCnt=3
TmrOpt=3
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="option_reg.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="option_reg.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="option_reg.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="option_reg.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=INTF
EnReg=intcon
EnBit=INTE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT"
Opt1_1Val="option_reg.INTEDG=1;\niocb = iocb | 0x01;\n"
Opt1_2="falling edge of RB0/INT"
Opt1_2Val="option_reg.INTEDG=0;\niocb = iocb | 0x01;\n"

[PORTB]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=RBIF
EnReg=intcon
EnBit=RBIE
OptCnt=4
TmrOpt=0
Opt1="Interrupt On Change Enable RB7:6"
Opt1Cnt=4
Opt1_1="B7 on; B6 on"
Opt1_1Val="iocb = iocb | 0xC0;\n"
Opt1_2="B7 on; B6 off"
Opt1_2Val="iocb = (iocb | 0x80) & 0xBF;\n"
Opt1_3="B7 off; B6 on"
Opt1_3Val="iocb = (iocb | 0x40) & 0x7F;\n"
Opt1_4="B7 off; B6 off"
Opt1_4Val="iocb = iocb & 0x3F;\n"
Opt2="Interrupt On Change Enable RB5:4"
Opt2Cnt=4
Opt2_1="B5 on; B4 on"
Opt2_1Val="iocb = iocb | 0x30;\n"
Opt2_2="B5 on; B4 off"
Opt2_2Val="iocb = (iocb | 0x20) & 0xEF;\n"
Opt2_3="B5 off; B4 on"
Opt2_3Val="iocb = (iocb | 0x10) & 0xDF;\n"
Opt2_4="B5 off; B4 off"
Opt2_4Val="iocb = iocb & 0xCF;\n"
Opt3="Interrupt On Change Enable RB3:2"
Opt3Cnt=4
Opt3_1="B3 on; B2 on"
Opt3_1Val="iocb = iocb | 0x0C;\n"
Opt3_2="B3 on; B2 off"
Opt3_2Val="iocb = (iocb | 0x08) & 0xFB;\n"
Opt3_3="B3 off; B2 on"
Opt3_3Val="iocb = (iocb | 0x04) & 0xF7;\n"
Opt3_4="B3 off; B2 off"
Opt3_4Val="iocb = iocb & 0xF3;\n"
Opt4="Interrupt On Change Enable RB1:0"
Opt4Cnt=4
Opt4_1="B1 on; B0 on"
Opt4_1Val="iocb = iocb | 0x03;\n"
Opt4_2="B1 on; B0 off"
Opt4_2Val="iocb = (iocb | 0x02) & 0xFE;\n"
Opt4_3="B1 off; B0 on"
Opt4_3Val="iocb = (iocb | 0x01) & 0xFD;\n"
Opt4_4="B1 off; B0 off"
Opt4_4Val="iocb = iocb & 0xFC;\n"