[Device]
Pins=8
Ports=1
ADCPins=4
ADCBits=10
MaxClock=20000000
PrescalerBits=3
ClockDivider=4
TimerOverflow=256
ConfigAddress=0x2007
ConfigCount=1
PWMCount=1
EepromSize=0
HasAltPWM=0
Pwm2IsD4=0
FlowcodeProduct=PIC
UsesGpio=1
DefaultPackageType=0

[Pins]
Pin1 = "VDD"
Pin2 = "GP5/OSC1"
Pin3 = "GP4/AN3/OSC2"
Pin4 = "GP3/MCLR"
Pin5 = "GP2/AN2/INT"
Pin6 = "GP1/AN1"
Pin7 = "GP0/AN0"
Pin8 = "VSS"

[Ports]
PortPin7=0x0000
PortPin6=0x0001
PortPin5=0x0002
PortPin4=0x0003
PortPin3=0x0004
PortPin2=0x0005

[PortMasks]
;Only bits 0-5 available on port A
PortMask0=0x3F

[ADCPins]
ADC0=7
ADC1=6
ADC2=5
ADC3=3

[Code]
;Substitute macros
;%c Clock Speed
;%o Operand
;%s Prescaler
;%p PortID
;%m MaskBits
;%i Inverse Mask
;%a ADC channel
;%a Config Address
;%v Config Value
;%r Interrupt Flag Register
;%b Interrupt Flag Bit
;%n Interrupt Macro Name
Directives="#include <system.h>\n#pragma CLOCK_FREQ %c\n"
MainStart="void main()\n{\n"
MainEnd="\tmainendloop: goto mainendloop;\n}\n\n"
IntStart="void interrupt(void)\n{\n"
IntEnd="}\n\n"
Initialise="ansel = 0;\n"
IntInit="option_reg = 0xC0;\n\n"
InputCmdFull="trisio = trisio | %m;\n%o = gpio;\n"
InputCmdOneBit="trisio = trisio | %m;\n%o = ((gpio & %m) == %m);\n"
InputCmdMask="trisio = trisio | %m;\n%o = gpio & %m;\n"
OutputCmdFull="trisio = 0x00;\ngpio = %o;\n"
OutputCmdOneBit="trisio = trisio & %i;\nif (%o)\n\tgpio = (gpio & %i) | %m;\nelse\n\tgpio = gpio & %i;\n"
OutputCmdMask="trisio = trisio & %i;\ngpio = (gpio & %i) | (%o & %m);\n"
DelayCmdS="delay_s(%o);\n"
DelayCmdMs="delay_ms(%o);\n"
ADCCapture="//set up ADC conversion\nchar old_tris, cnt;\n#define MX_ADC_SAMP_TIME 40\n#define MX_ADC_TRIS_REG  trisio\n\n//find appropriate bit\n#if (%a == 0)\n  #define MX_ADC_TRIS_MSK  0x01\n  #define MX_ADC_ANS_MSK   0x01\n#endif\n#if (%a == 1)\n  #define MX_ADC_TRIS_MSK  0x02\n  #define MX_ADC_ANS_MSK   0x02\n#endif\n#if (%a == 2)\n  #define MX_ADC_TRIS_MSK  0x04\n  #define MX_ADC_ANS_MSK   0x04\n#endif\n#if (%a == 3)\n  #define MX_ADC_TRIS_MSK  0x10\n  #define MX_ADC_ANS_MSK   0x08\n#endif\n\n//sanity check\n#ifndef MX_ADC_TRIS_MSK\n  #pragma error ADC conversion code error - please contact technical support\n#endif\n\n//store old tris value, and set the i/o pin as an input\nold_tris = MX_ADC_TRIS_REG;\nMX_ADC_TRIS_REG = MX_ADC_TRIS_REG | MX_ADC_TRIS_MSK;\nansel = 0x20 | MX_ADC_ANS_MSK;\n\n//turn ADC on\nadcon0 = 0x01 | (%a << 2);\n\n//wait the acquisition time\ncnt =0;\nwhile (cnt <40) cnt++;\n\n//begin conversion and wait until it has finished\nadcon0 = adcon0 | 0x02;\nwhile (adcon0 & 0x02) ;\n\n//restore old tris value, and reset adc registers\ntrisio = old_tris;\nansel = 0x20;\nadcon0 = 0x00;\n#undef MX_ADC_TRIS_REG\n#undef MX_ADC_TRIS_MSK\n#undef MX_ADC_SAMP_TIME\n#undef MX_ADC_ANS_MSK\n"
ADCHigh="return adresh;\n"
ADCLow="char adclow;\nadclow = adresl;\nreturn adclow;\n"
ADCFull="short iRetVal;\niRetVal = (adresh << 2);\niRetVal += (adresl >> 6);\nreturn (iRetVal);\n"
InitialPortLetter="a"
ConfigData="#pragma DATA %a, %v\n"
IntHandler="if (%r & (1 << %b))\n{\n\tFCM_%n();\n\tclear_bit(%r, %b);\n}\n"

[Defines]
Define1=#define P12F615
Define2=#define MX_PWM
Define3=#define MX_PWM_CNT 1
Define4=#define MX_PWM_TRIS1 trisio
Define5=#define MX_PWM_1 2

[Interrupts]
;first 3 should always be 1=TMR0, 2=RB0INT, 3=PORTB
;any other interrupts need to also have this set: "intcon.PEIE=1;\n"
GeneralInit="intcon.GIE=1;\n"
Count=4
1=TMR0
2=RB0INT
3=PORTB
4=TMR1



[TMR0]
;it is vital that this section remains exactly as-is (for all chips?)
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=T0IF
EnReg=intcon
EnBit=T0IE
OptCnt=3
TmrOpt=3
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T0CKI pin"
Opt1_1Val="option_reg.T0CS=1;\n"
Opt1_2="Internal clock (CLKO)"
Opt1_2Val="option_reg.T0CS=0;\n"
Opt2="Source Edge Select"
Opt2Cnt=2
Opt2_1="high-to-low transition on T0CKI"
Opt2_1Val="option_reg.T0SE=1;\n"
Opt2_2="low-to-high transition on T0CKI"
Opt2_2Val="option_reg.T0SE=0;\n"
Opt3="Prescaler Rate"
Opt3Cnt=9
Opt3_1="1:1"
Opt3_1Val="option_reg = (option_reg & 0xF0) | 0x08;\n"
Opt3_2="1:2"
Opt3_2Val="option_reg = (option_reg & 0xF0) | 0x00;\n"
Opt3_3="1:4"
Opt3_3Val="option_reg = (option_reg & 0xF0) | 0x01;\n"
Opt3_4="1:8"
Opt3_4Val="option_reg = (option_reg & 0xF0) | 0x02;\n"
Opt3_5="1:16"
Opt3_5Val="option_reg = (option_reg & 0xF0) | 0x03;\n"
Opt3_6="1:32"
Opt3_6Val="option_reg = (option_reg & 0xF0) | 0x04;\n"
Opt3_7="1:64"
Opt3_7Val="option_reg = (option_reg & 0xF0) | 0x05;\n"
Opt3_8="1:128"
Opt3_8Val="option_reg = (option_reg & 0xF0) | 0x06;\n"
Opt3_9="1:256"
Opt3_9Val="option_reg = (option_reg & 0xF0) | 0x07;\n"

[RB0INT]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=INTF
EnReg=intcon
EnBit=INTE
OptCnt=1
TmrOpt=0
Opt1="Interrupt Edge Select"
Opt1Cnt=2
Opt1_1="rising edge of RB0/INT"
Opt1_1Val="option_reg.INTEDG=1;\n"
Opt1_2="falling edge of RB0/INT"
Opt1_2Val="option_reg.INTEDG=0;\n"

[PORTB]
Name=(this is retrieved from the resource file)
FlagReg=intcon
FlagBit=GPIF
EnReg=intcon
EnBit=GPIE
OptCnt=3
TmrOpt=0
Opt1="IOC Enable GP0:GP1"
Opt1Cnt=4
Opt1_1="GPIO 0 Int On / GPIO 1 Int On"
Opt1_1Val="ioc = ioc | 0x03;\n"
Opt1_2="GPIO 0 Int On / GPIO 1 Int Off"
Opt1_2Val="ioc = (ioc | 0x01) & 0xFD;\n"
Opt1_3="GPIO 0 Int Off / GPIO 1 Int On"
Opt1_3Val="ioc = (ioc | 0x02) & 0xFE;\n"
Opt1_4="GPIO 0 Int Off / GPIO 1 Int Off"
Opt1_4Val="ioc = ioc & 0xFC;\n"
Opt2="IOC Enable GP2:GP3"
Opt2Cnt=4
Opt2_1="GPIO 2 Int On / GPIO 3 Int On"
Opt2_1Val="ioc = ioc | 0x0C;\n"
Opt2_2="GPIO 2 Int On / GPIO 3 Int Off"
Opt2_2Val="ioc = (ioc | 0x04) & 0xFB;\n"
Opt2_3="GPIO 2 Int Off / GPIO 3 Int On"
Opt2_3Val="ioc = (ioc | 0x08) & 0xF7;\n"
Opt2_4="GPIO 2 Int Off / GPIO 3 Int Off"
Opt2_4Val="ioc = ioc & 0xF3;\n"
Opt3="IOC Enable GP4:GP5"
Opt3Cnt=4
Opt3_1="GPIO 4 Int On / GPIO 5 Int On"
Opt3_1Val="ioc = ioc | 0x30;\n"
Opt3_2="GPIO 4 Int On / GPIO 5 Int Off"
Opt3_2Val="ioc = (ioc | 0x10) & 0xDF;\n"
Opt3_3="GPIO 4 Int Off / GPIO 5 Int On"
Opt3_3Val="ioc = (ioc | 0x20) & 0xEF;\n"
Opt3_4="GPIO 4 Int Off / GPIO 5 Int Off"
Opt3_4Val="ioc = ioc & 0xCF;\n"

[TMR1]
;NOTE: this osc is enabled and turned on as part of the Opt1 code
Name="TMR1 Overflow"
FlagReg=pir1
FlagBit=TMR1IF
EnReg=pie1
EnBit=TMR1IE
OptCnt=2
TmrOpt=2
Opt1="Clock Source Select"
Opt1Cnt=2
Opt1_1="Transition on T1CKI pin"
Opt1_1Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=1;\n"
Opt1_2="Internal clock (Fosc/4)"
Opt1_2Val="intcon.PEIE=1;\nt1con.T1OSCEN=1;\nt1con.TMR1ON=1;\nt1con.TMR1CS=0;\n"
Opt2="Prescaler Rate"
Opt2Cnt=4
Opt2_1="1:1"
Opt2_1Val="t1con = t1con & 0x0F;\n"
Opt2_2="1:2"
Opt2_2Val="t1con = (t1con & 0x0F) | 0x10;\n"
Opt2_3="1:4"
Opt2_3Val="t1con = (t1con & 0x0F) | 0x20;\n"
Opt2_4="1:8"
Opt2_4Val="t1con = (t1con & 0x0F) | 0x30;\n"