//************************************************************************************ //** //** File name: H:\Kundendaten\Strunk\Projekt Rufsystem\Flowcode Software\Code_is_ready\Empfangseinheit_mit Klartextnamen_und Klartextabteilungen\07-06-2012\FC5\16F887_Empfaenger.c //** Title: //** Description: //** //** Generated by: Flowcode v5.2.0.0 //** Date: Thursday, June 07, 2012 19:08:27 //** Licence: Professional //** Registered to: Ing. Buero REMANE //** Licence key: 4E59BK //** //** //** http://www.matrixmultimedia.com //** //************************************************************************************ #define MX_PIC #define MX_USES_UINT8 1 #define MX_USES_SINT16 0 #define MX_USES_CHAR 2 #define MX_USES_FLOAT 0 #define MX_USES_SINT32 0 #define MX_USES_BOOL 0 #define MX_USES_UINT16 0 #define MX_USES_UINT32 0 //Definitionen für Microcontroller #define P16F887 #define FC_CAL_PIC #define MX_ADC #define MX_ADC_TYPE_7 #define MX_ADC_BITS_10 #define MX_EE #define MX_EE_TYPE2 #define MX_EE_SIZE 256 #define MX_SPI_1 #define MX_SPI_1_MISO_PORT portc #define MX_SPI_1_MISO_TRIS trisc #define MX_SPI_1_MISO_PIN 4 #define MX_SPI_1_MOSI_PORT portc #define MX_SPI_1_MOSI_TRIS trisc #define MX_SPI_1_MOSI_PIN 5 #define MX_SPI_1_CLK_PORT portc #define MX_SPI_1_CLK_TRIS trisc #define MX_SPI_1_CLK_PIN 3 #define MX_SPI_1_SS_PORT portc #define MX_SPI_1_SS_TRIS trisc #define MX_UART_1 #define MX_UART_1_TX_PORT portc #define MX_UART_1_TX_TRIS trisc #define MX_UART_1_TX_PIN 6 #define MX_UART_1_RX_PORT portc #define MX_UART_1_RX_TRIS trisc #define MX_UART_1_RX_PIN 7 #define MX_I2C #define MX_MI2C #define MX_I2C_1 #define MX_I2C_1_SDA_PORT portc #define MX_I2C_1_SDA_TRIS trisc #define MX_I2C_1_SDA_PIN 4 #define MX_I2C_1_SCL_PORT portc #define MX_I2C_1_SCL_TRIS trisc #define MX_I2C_1_SCL_PIN 3 #define MX_PWM #define MX_PWM_CNT 2 #define MX_PWM_PSCA1 #define MX_PWM_PSCA4 #define MX_PWM_PSCA16 #define MX_PWM_1_PORT portc #define MX_PWM_1_TRIS trisc #define MX_PWM_1_PIN 2 #define MX_PWM_2_PORT portc #define MX_PWM_2_TRIS trisc #define MX_PWM_2_PIN 1 //Funktionen #define MX_CLK_SPEED 4000000 #ifdef _BOOSTC #include #endif #ifdef HI_TECH_C #include #endif //Konfigurations-Daten #ifdef _BOOSTC #pragma DATA 0x2007, 0x20c4 #endif #ifdef HI_TECH_C __CONFIG(0x20c4); #endif #ifdef _BOOSTC #pragma DATA 0x2008, 0x3fff #endif #ifdef HI_TECH_C __CONFIG(0x3fff); #endif //Interne Funktionen #include "C:\Program Files (x86)\Flowcode\v5\FCD\internals.c" //Makro-Funktions-Deklarationen void FCM_Split_Buffer(); void FCM_Show(); void FCM_Buzzer(); void FCM_Error(); //Variablen-Deklarationen #define FCSZ_ABTEILUNG_TEXT 16 #define FCSZ_PERSON 16 MX_UINT8 FCV_RF_BYTE_READ; MX_UINT8 FCV_ABTEILUNG; MX_CHAR FCV_ABTEILUNG_TEXT[FCSZ_ABTEILUNG_TEXT]; MX_UINT8 FCV_STOERUNG; MX_CHAR FCV_PERSON[FCSZ_PERSON]; MX_UINT8 FCV_TASTER; MX_UINT8 FCV_BUFFER; MX_UINT8 FCLV_LOOP1; //RF(0): //Defines: /**** Macro Substitutions **** a = Unique Reference b = SPI Channel 0-SW / 1-HW SPI1 / 2-HW SPI2 / 3-HW SPI3 .... c = MOSI Pin d = MOSI Port e = MISO Pin f = MISO Port g = SCK Pin h = SCK Port i = CS Pin j = CS Port k = FSEL Pin l = FSEL Port m = Frequency Selection 1-433MHz 2-868MHz 3-915MHz n = Centre Frequency Channel selection - 96-3903 See Calculation p28 o = Baud Rate See Calculation p37 p = Receiver Bandwidth q = Receiver Gain r = Receiver Threshold s = Transmitter Deviation t = Transmitter Power Output u = Transmitter Duty Cycle Setting v = Data Mode w = Preamble Sync ID Value x = Extended Preamble Sync ID Enable ******************************/ #define MX_RF_CHANNEL 0 //Definitions for SDI control - need access to spi pin in application #if (MX_RF_CHANNEL == 0) //software spi #define RF_2_MX_RF_SDI_PIN 7 #define RF_2_MX_RF_SDI_PORT portd #define RF_2_MX_RF_SDI_TRIS trisd #endif #if (MX_RF_CHANNEL == 1) //channel 1 #define RF_2_MX_RF_SDI_PIN MX_SPI_1_MISO_PIN #define RF_2_MX_RF_SDI_PORT MX_SPI_1_MISO_PORT #define RF_2_MX_RF_SDI_TRIS MX_SPI_1_MISO_TRIS #endif #if (MX_RF_CHANNEL == 2) //channel 2 #define RF_2_MX_RF_SDI_PIN MX_SPI_2_MISO_PIN #define RF_2_MX_RF_SDI_PORT MX_SPI_2_MISO_PORT #define RF_2_MX_RF_SDI_TRIS MX_SPI_2_MISO_TRIS #endif //Definitions for CS control #define RF_2_MX_RF_CS_PIN 5 #define RF_2_MX_RF_CS_PORT portd #define RF_2_MX_RF_CS_TRIS trisd //Definitions for FSEL Pin #define RF_2_MX_RF_FSEL_PIN 3 #define RF_2_MX_RF_FSEL_PORT portd #define RF_2_MX_RF_FSEL_TRIS trisd //Definitions for SPI slot allocation #ifndef MX_SPI_REF1 #define MX_SPI_REF1 #define RF_2_MX_SPI_UREF 1 #define MX_SPI_CHANNEL_1 0 #define MX_SPI_MOSI_PIN_1 4 #define MX_SPI_MOSI_PORT_1 portd #define MX_SPI_MOSI_TRIS_1 trisd #define MX_SPI_MISO_PIN_1 7 #define MX_SPI_MISO_PORT_1 portd #define MX_SPI_MISO_TRIS_1 trisd #define MX_SPI_SCK_PIN_1 6 #define MX_SPI_SCK_PORT_1 portd #define MX_SPI_SCK_TRIS_1 trisd #define MX_SPI_CS_PIN_1 0 #define MX_SPI_CS_PORT_1 0 #define MX_SPI_BMODE_1 2 #define MX_SPI_PR_SCALE_1 4 #define MX_SPI_PO_SCALE_1 0 #define MX_SPI_INT_1 0 #else #ifndef MX_SPI_REF2 #define MX_SPI_REF2 #define RF_2_MX_SPI_UREF 2 #define MX_SPI_CHANNEL_2 0 #define MX_SPI_MOSI_PIN_2 4 #define MX_SPI_MOSI_PORT_2 portd #define MX_SPI_MOSI_TRIS_2 trisd #define MX_SPI_MISO_PIN_2 7 #define MX_SPI_MISO_PORT_2 portd #define MX_SPI_MISO_TRIS_2 trisd #define MX_SPI_SCK_PIN_2 6 #define MX_SPI_SCK_PORT_2 portd #define MX_SPI_SCK_TRIS_2 trisd #define MX_SPI_CS_PIN_2 0 #define MX_SPI_CS_PORT_2 0 #define MX_SPI_BMODE_2 2 #define MX_SPI_PR_SCALE_2 4 #define MX_SPI_PO_SCALE_2 0 #define MX_SPI_INT_2 0 #else #ifndef MX_SPI_REF3 #define MX_SPI_REF3 #define RF_2_MX_SPI_UREF 3 #define MX_SPI_CHANNEL_3 0 #define MX_SPI_MOSI_PIN_3 4 #define MX_SPI_MOSI_PORT_3 portd #define MX_SPI_MOSI_TRIS_3 trisd #define MX_SPI_MISO_PIN_3 7 #define MX_SPI_MISO_PORT_3 portd #define MX_SPI_MISO_TRIS_3 trisd #define MX_SPI_SCK_PIN_3 6 #define MX_SPI_SCK_PORT_3 portd #define MX_SPI_SCK_TRIS_3 trisd #define MX_SPI_CS_PIN_3 0 #define MX_SPI_CS_PORT_3 0 #define MX_SPI_BMODE_3 2 #define MX_SPI_PR_SCALE_3 4 #define MX_SPI_PO_SCALE_3 0 #define MX_SPI_INT_3 0 #else #ifndef MX_SPI_REF4 #define MX_SPI_REF4 #define RF_2_MX_SPI_UREF 4 #define MX_SPI_CHANNEL_4 0 #define MX_SPI_MOSI_PIN_4 4 #define MX_SPI_MOSI_PORT_4 portd #define MX_SPI_MOSI_TRIS_4 trisd #define MX_SPI_MISO_PIN_4 7 #define MX_SPI_MISO_PORT_4 portd #define MX_SPI_MISO_TRIS_4 trisd #define MX_SPI_SCK_PIN_4 6 #define MX_SPI_SCK_PORT_4 portd #define MX_SPI_SCK_TRIS_4 trisd #define MX_SPI_CS_PIN_4 0 #define MX_SPI_CS_PORT_4 0 #define MX_SPI_BMODE_4 2 #define MX_SPI_PR_SCALE_4 4 #define MX_SPI_PO_SCALE_4 0 #define MX_SPI_INT_4 0 #endif #endif #endif #endif #define RF_2_SPI_Master_Init CAL_APPEND(FC_CAL_SPI_Master_Init_, RF_2_MX_SPI_UREF) #define RF_2_SPI_Master_Byte CAL_APPEND(FC_CAL_SPI_Master_Byte_, RF_2_MX_SPI_UREF) extern void RF_2_SPI_Master_Init (); extern MX_UINT8 RF_2_SPI_Master_Byte (MX_UINT8 DataOut); //Duty cycle limit when using the 868MHz band in Europe!!! //common defines #define MX_RF_FREQ 2 //Module Frequency #define MX_RF_CFREQ 2000 //Central Frequency 96 <-> 3903 (0x7D0) #define MX_RF_BAUD 17 //Data Baud Rate (0x23) #define MX_RF_BWIDTH (3 + 1) //Bandwithd 0= / 6= #define MX_RF_GAIN 0 //Gain 0= / 3= #define MX_RF_THRESH 0 //Threshold 0= / 5= #define MX_RF_DVN 7 //Deviation 0=15KHz / 15=240KHz #define MX_RF_PWR 0 //Power 0=0dB / 7=-17.5dB #define MX_RF_DUTY 100 #define MX_RF_DATAMODE 0 //Data mode - I/O or Data #define MX_RF_ID 85 //Sync ID #define MX_RF_EXTID ((1 - 1) * 8) //Extended Sync 0=Off / 1=On #define MX_RF_TXPROP ((MX_RF_DVN << 4) | MX_RF_PWR) #define MX_RF_BUFFER_MAX 8 // General commands #define GENCREG (0x8008 | (MX_RF_FREQ << 4)) //RF_Frequency does not change.... #define PMCREG 0x8200 #define CFSREG 0xA000 // Data commands #define DATARATE 0xC600 #define SYNCHRON 0xCE00 // RX commands #define RXCREG 0x9000 #define RXBREG 0xB000 #define FIFORSTREG 0xCA81 //0xCA85 #define BBFCREG 0xC22C #define AFCCREG 0xC4D7 // TX commands #define TXCREG 0x9800 #define TXBREG 0xB800 // Preloaded commands with data #define PDOWN 0x8201 MX_UINT8 MX_RF_Mode; MX_UINT8 MX_RF_Sync = MX_RF_ID; MX_UINT8 MX_RF_RX_Buffer[MX_RF_BUFFER_MAX + 2]; MX_UINT8 MX_RF_RX_Buff1[MX_RF_BUFFER_MAX + 2]; MX_UINT8 MX_RF_TX_Buffer[MX_RF_BUFFER_MAX + 2]; //RF(0): //Makro-Funktions-Deklarationen void FCD_RF0_SPI_Byte16(MX_SINT16 spicmd); MX_SINT16 FCD_RF0_SPI_Command(MX_SINT16 spicmd); void FCD_RF0_Wait_For_SDI(); MX_SINT16 FCD_RF0_Init_RF_Module(); void FCD_RF0_Uninit_RF_Module(); void FCD_RF0_Send_Byte(MX_UINT8 Data); void FCD_RF0_Send_String(MX_STRING String, MX_UINT8 MSZ_String); MX_UINT8 FCD_RF0_Receive_Byte(MX_UINT8 Timeout); void FCD_RF0_Receive_String(MX_CHAR* FCR_RETVAL, MX_UINT8 FCR_RETVAL_SIZE, MX_UINT8 Length, MX_UINT8 Timeout); void FCD_RF0_Activate_RX_Mode(); void FCD_RF0_Activate_TX_Mode(); void FCD_RF0_Update_Centre_Frequency(MX_SINT16 Frequency); void FCD_RF0_Set_Sync_Pattern(MX_UINT8 Mode, MX_UINT8 Pattern); void FCD_RF0_RX_Tune(MX_UINT8 Bandwidth, MX_UINT8 Gain, MX_UINT8 Threshold); void FCD_RF0_TX_Tune(MX_UINT8 Deviation, MX_UINT8 Power); void FCD_RF0_Set_Data_Rate(MX_UINT8 Rate); MX_UINT8 FCD_RF0_Read_RX_Signal_Strength(); void FCD_RF0_FSK_Write(MX_UINT8 State); MX_UINT8 FCD_RF0_FSK_Read(); void FCD_RF0_Set_Buffer_Data(MX_UINT8 Index, MX_UINT8 Data); void FCD_RF0_Send_Buffer(MX_UINT8 Count); MX_UINT8 FCD_RF0_Check_Buffer(MX_UINT8 Timeout); MX_UINT8 FCD_RF0_Get_Data_Count(); MX_UINT8 FCD_RF0_Get_Buffer_Data(MX_UINT8 Index); //LCDDisplay(0): //Defines: /**** Macro Substitutions **** a = Unique Component Reference Number b = D1 Port Letter c = D2 Port Letter d = D3 Port Letter e = D4 Port Letter f = RS Port Letter g = E Port Letter h = Data 1_Pin i = Data 2 Pin j = Data 3 Pin k = Data 4 Pin l = RS Pin m = Enable Pin n = Row Count o = Column Count ******************************/ //component connections #define LCD_3__PORT0 porta #define LCD_3__PORT1 porta #define LCD_3__PORT2 porta #define LCD_3__PORT3 porta #define LCD_3__PORT4 porta #define LCD_3__PORT5 porta #define LCD_3__TRIS0 trisa #define LCD_3__TRIS1 trisa #define LCD_3__TRIS2 trisa #define LCD_3__TRIS3 trisa #define LCD_3__TRIS4 trisa #define LCD_3__TRIS5 trisa #define LCD_3__BIT0 2 #define LCD_3__BIT1 3 #define LCD_3__BIT2 4 #define LCD_3__BIT3 5 #define LCD_3__RS 0 #define LCD_3__E 1 #define LCD_3__ROWCNT 2 #define LCD_3__COLCNT 16 #ifdef _BOOSTC #define LCD_3__DELAY delay_10us(10) #endif #ifdef _C2C_ #define LCD_3__DELAY delay_us(100) #endif #ifdef HI_TECH_C #define LCD_3__DELAY __delay_us(120) #endif #ifndef LCD_3__DELAY #define LCD_3__DELAY delay_us(100) #endif //LCDDisplay(0): //Makro-Funktions-Deklarationen void FCD_LCDDisplay0_RawSend(MX_UINT8 in, MX_UINT8 mask); void FCD_LCDDisplay0_Start(); void FCD_LCDDisplay0_Clear(); void FCD_LCDDisplay0_PrintASCII(MX_UINT8 Character); void FCD_LCDDisplay0_Command(MX_UINT8 in); void FCD_LCDDisplay0_Cursor(MX_UINT8 x, MX_UINT8 y); void FCD_LCDDisplay0_PrintNumber(MX_SINT16 Number); void FCD_LCDDisplay0_PrintString(MX_STRING String, MX_UINT8 MSZ_String); void FCD_LCDDisplay0_ScrollDisplay(MX_UINT8 Direction, MX_UINT8 Num_Positions); void FCD_LCDDisplay0_ClearLine(MX_UINT8 Line); void FCD_LCDDisplay0_RAM_Write(MX_UINT8 nIdx, MX_UINT8 d0, MX_UINT8 d1, MX_UINT8 d2, MX_UINT8 d3, MX_UINT8 d4, MX_UINT8 d5, MX_UINT8 d6, MX_UINT8 d7); //RF(0): //Makro-Implementierungen void FCD_RF0_SPI_Byte16(MX_SINT16 spicmd) { unsigned char temp; temp = spicmd >> 8; RF_2_SPI_Master_Byte(temp); // Send Upper Command Byte temp = spicmd & 0xFF; RF_2_SPI_Master_Byte(temp); // Send Lower Command Byte } MX_SINT16 FCD_RF0_SPI_Command(MX_SINT16 spicmd) { unsigned int retval; unsigned char temp; FC_CAL_Bit_Low(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Clear Chip Select bit delay_us(1); temp = spicmd >> 8; retval = RF_2_SPI_Master_Byte(temp); // Send Upper Command Byte retval = retval << 8; temp = spicmd & 0xFF; retval = retval | RF_2_SPI_Master_Byte(temp); // Send Lower Command Byte delay_us(1); FC_CAL_Bit_High(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Set Chip Select bit delay_us(1); return retval; } void FCD_RF0_Wait_For_SDI() { while(FC_CAL_Bit_In(RF_2_MX_RF_SDI_PORT, RF_2_MX_RF_SDI_PIN) == 0); //Wait for SDI Input } MX_SINT16 FCD_RF0_Init_RF_Module() { unsigned int Retval; FC_CAL_Bit_High_DDR(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_TRIS, RF_2_MX_RF_CS_PIN); //Setup CS Pin RF_2_SPI_Master_Init(); //Call SPI initialise function delay_ms(100); //100ms Delay to ensure transceiver has powered up // Configuring the RF link FCD_RF0_SPI_Command(FIFORSTREG); //Disable (Sensitive) Reset Mode FCD_RF0_SPI_Command(FIFORSTREG | MX_RF_EXTID | 0x02); //Restart Synchronous MX_UINT8acter pattern recognition FCD_RF0_SPI_Command(GENCREG); //Assign frequency band and set load capacitance FCD_RF0_SPI_Command(CFSREG | MX_RF_CFREQ); //Set Channel Center Frequency FCD_RF0_SPI_Command(DATARATE | MX_RF_BAUD); //Set Data Rate FCD_RF0_SPI_Command(PMCREG); //Turn Off TX and RX controller chains Retval = (MX_RF_BWIDTH << 5) | (MX_RF_GAIN << 3) | MX_RF_THRESH; FCD_RF0_SPI_Command(RXCREG | Retval); //Enable Data RX Output / Set signal strengths and gain FCD_RF0_SPI_Command(SYNCHRON | MX_RF_Sync); FCD_RF0_SPI_Command(TXCREG | MX_RF_TXPROP); //Set TX frequency deviation // Antenna Tuning FCD_RF0_SPI_Command( PMCREG | 0x0020); //Turn on TX baseband circuit delay_ms(5); //Wait for oscillatr to stabilise // Set Up The Receiver FCD_RF0_SPI_Command(PMCREG | 0x0080); //Turn off Tx, turn on receiver Retval = FCD_RF0_SPI_Command(0); //Read back and return STSREG Retval = FCD_RF0_SPI_Command(0); //Read back and return STSREG Retval = FCD_RF0_SPI_Command(0); //Read back and return STSREG Retval = FCD_RF0_SPI_Command(0); //Read back and return STSREG Retval = FCD_RF0_SPI_Command(0); //Read back and return STSREG #if (MX_RF_DATAMODE == 0) FCD_RF0_SPI_Command(GENCREG | 0x0040); //Enable the FIFO FCD_RF0_SPI_Command(FIFORSTREG); FCD_RF0_SPI_Command(FIFORSTREG | MX_RF_EXTID | 0x02); //Restart Synchronous character pattern recognition FC_CAL_Bit_High_DDR(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_TRIS, RF_2_MX_RF_FSEL_PIN); MX_RF_Mode = 0; #else FC_CAL_Bit_In_DDR(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_TRIS, RF_2_MX_RF_FSEL_PIN); FCD_RF0_SPI_Command(GENCREG); //Leave the FIFO disabled MX_RF_Mode = 2; #endif return (Retval); } void FCD_RF0_Uninit_RF_Module() { FCD_RF0_SPI_Command(PDOWN); } void FCD_RF0_Send_Byte(MX_UINT8 Data) { FCD_RF0_Set_Buffer_Data(0, Data); //Pass byte into send buffer FCD_RF0_Send_Buffer(1); //Send buffer } void FCD_RF0_Send_String(MX_STRING String, MX_UINT8 MSZ_String) { MX_UINT8 Ptr; MX_UINT8 Length; Length = MSZ_String; for (Ptr = 0; Ptr < Length; Ptr++) //For each character in string { FCD_RF0_Set_Buffer_Data(Ptr, String[Ptr]); //Pass string into send buffer if (String[Ptr] == 0) //Is there a null byte in the string? Length = Ptr; //If so then we are at the end } FCD_RF0_Send_Buffer(Length); //Send buffer } MX_UINT8 FCD_RF0_Receive_Byte(MX_UINT8 Timeout) { MX_UINT8 retVal; retVal = FCD_RF0_Check_Buffer(Timeout); //Check for incoming data if (retVal == 1) //If 1 byte received retVal = FCD_RF0_Get_Buffer_Data(0); //Collect byte else return 255; //Or return timeout err return retVal; } void FCD_RF0_Receive_String(MX_CHAR* FCR_RETVAL, MX_UINT8 FCR_RETVAL_SIZE, MX_UINT8 Length, MX_UINT8 Timeout) { MX_UINT8 dcount, idx; FCR_RETVAL[0] = 0; //Begin by assigning null to string dcount = FCD_RF0_Check_Buffer(Timeout); //Check for incoming data if (dcount < 250) //Valid packet size received? { for (idx = 0; idx < Length; idx++) //Loop through specified received bytes { if (idx < FCR_RETVAL_SIZE) //Is there still room in the buffer? { if (idx < dcount) //Have we received all available bytes? { FCR_RETVAL[idx] = FCD_RF0_Get_Buffer_Data(idx); //Collect byte and add to string if (FCR_RETVAL[idx] == 0) //If null byte received Length = idx; //Finish collecting bytes } } } if (idx < FCR_RETVAL_SIZE) //If string is not full FCR_RETVAL[idx] = 0; //Then add a null byte just incase there was not one in the received data } } void FCD_RF0_Activate_RX_Mode() { FCD_RF0_SPI_Command(PMCREG | 0x0080); // turn off Tx, turn on the receiver if (MX_RF_Mode == 0) // Set system mode value { FCD_RF0_SPI_Command(GENCREG | 0x0040); // disable the Tx register, Enable the FIFO FCD_RF0_SPI_Command(FIFORSTREG); FCD_RF0_SPI_Command(FIFORSTREG | MX_RF_EXTID | 0x0002); //Reset FIFO FC_CAL_Bit_High_DDR(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_TRIS, RF_2_MX_RF_FSEL_PIN); //FSEL pin as output } else { FC_CAL_Bit_In_DDR(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_TRIS, RF_2_MX_RF_FSEL_PIN); //FSEL pin as input FCD_RF0_SPI_Command(GENCREG); //Leave the FIFO disabled } } void FCD_RF0_Activate_TX_Mode() { FCD_RF0_SPI_Command(PMCREG); // Turn off the transmitter and receiver if (MX_RF_Mode == 1) { FCD_RF0_SPI_Command(GENCREG | 0x0080); // Enable the Tx register } else { FCD_RF0_SPI_Command(GENCREG); // disable the Tx register and the FIFO } FCD_RF0_SPI_Command(PMCREG | 0x0020); // Turn on tx FC_CAL_Bit_High_DDR(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_TRIS, RF_2_MX_RF_FSEL_PIN); //FSEL pin as output } void FCD_RF0_Update_Centre_Frequency(MX_SINT16 Frequency) { if (Frequency < 96) Frequency = 96; if (Frequency > 3903) Frequency = 3903; FCD_RF0_SPI_Command(CFSREG | Frequency); } void FCD_RF0_Set_Sync_Pattern(MX_UINT8 Mode, MX_UINT8 Pattern) { MX_RF_Sync = Pattern; FCD_RF0_SPI_Command(FIFORSTREG); if (Mode) { //Word type synchronisation FCD_RF0_SPI_Command(FIFORSTREG | 0x02); } else { //Byte type synchronisation FCD_RF0_SPI_Command(FIFORSTREG | 0x0a); } FCD_RF0_SPI_Command(SYNCHRON | MX_RF_Sync); } void FCD_RF0_RX_Tune(MX_UINT8 Bandwidth, MX_UINT8 Gain, MX_UINT8 Threshold) { unsigned int TuneVals; if (Bandwidth > 6) Bandwidth = 6; if (Bandwidth < 1) Bandwidth = 1; if (Gain > 3) Gain = 3; if (Threshold > 5) Threshold = 5; TuneVals = RXCREG; TuneVals = TuneVals | (Bandwidth << 5); TuneVals = TuneVals | (Gain << 3); TuneVals = TuneVals | Threshold; FCD_RF0_SPI_Command(TuneVals); } void FCD_RF0_TX_Tune(MX_UINT8 Deviation, MX_UINT8 Power) { MX_UINT8 MX_RF_TxProps; if (Deviation > 15) Deviation = 15; if (Power > 7) Power = 7; MX_RF_TxProps = Deviation << 4; MX_RF_TxProps = MX_RF_TxProps | Power; FCD_RF0_SPI_Command(TXCREG | MX_RF_TxProps); } void FCD_RF0_Set_Data_Rate(MX_UINT8 Rate) { MX_UINT8 cs = 0; unsigned long r; r = 100000 / (29 * Rate); //10 x data rate value r = r + 5; //round up r = r / 10; //divide by 10 if (r > 0x80) //result too large { cs = 0x80; //set cs bit r >>= 2; //divide by 4 if (r & 0x01) r = r + 1; //round up r >>= 1; //divide by 2 } r = r - 1; FCD_RF0_SPI_Command(DATARATE | cs | (MX_UINT8)r); } MX_UINT8 FCD_RF0_Read_RX_Signal_Strength() { unsigned int test = 0; test = FCD_RF0_SPI_Command(0); //Read back and return STSREG test = test >> 6; //Rotate so that data we want is one bits 0 and 1 test = test & 0x07; //Mask off any unwanted values return (test); } void FCD_RF0_FSK_Write(MX_UINT8 State) { if(MX_RF_Mode != 3) { MX_RF_Mode = 3; //Set system mode value FCD_RF0_Activate_TX_Mode(); } if(State) FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); else FC_CAL_Bit_Low(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); } MX_UINT8 FCD_RF0_FSK_Read() { if (MX_RF_Mode != 2) { MX_RF_Mode = 2; FCD_RF0_Activate_RX_Mode(); } return(FC_CAL_Bit_In(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN)); } void FCD_RF0_Set_Buffer_Data(MX_UINT8 Index, MX_UINT8 Data) { if (Index < MX_RF_BUFFER_MAX) MX_RF_TX_Buffer[Index + 1] = Data; } void FCD_RF0_Send_Buffer(MX_UINT8 Count) { MX_UINT8 Data; MX_UINT8 Ptr; MX_UINT8 NextByte = 1; MX_UINT8 Csum = 0; if (Count < MX_RF_BUFFER_MAX) { MX_RF_TX_Buffer[0] = Count; //Calculate checksum for(Ptr = 0; Ptr <= Count; Ptr++) Csum ^= MX_RF_TX_Buffer[Ptr]; MX_RF_TX_Buffer[Ptr] = Csum; //Include count and checksum Count += 2; //Set Tx mode if (MX_RF_Mode != 1) //If we are in receive mode { MX_RF_Mode = 1; FCD_RF0_Activate_TX_Mode(); //Switch to transmit mode } FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 1 FC_CAL_Bit_Low(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Clear Chip Select bit delay_us(1); // FCD_RF0_Wait_For_SDI(); FCD_RF0_SPI_Byte16(TXBREG | 0xAA); // preamble #if (MX_RF_EXTID == 0) FCD_RF0_Wait_For_SDI(); //Wait for SDI Input FCD_RF0_SPI_Byte16(TXBREG | 0x2D); // sync pattern 1st byte (optional) #endif FCD_RF0_Wait_For_SDI(); //Wait for SDI Input FCD_RF0_SPI_Byte16(TXBREG | MX_RF_Sync); // sync pattern 2nd byte Ptr = 0; Data = MX_RF_TX_Buffer[Ptr++]; while(NextByte) { FCD_RF0_Wait_For_SDI(); //Wait for SDI Input FCD_RF0_SPI_Byte16(TXBREG | Data); // write byte to tx register Data = MX_RF_TX_Buffer[Ptr]; if(Ptr == Count) NextByte = 0; Ptr++; } FCD_RF0_Wait_For_SDI(); //Wait for SDI Input FCD_RF0_SPI_Byte16(TXBREG | 0x00); // write a dummy byte since the previous byte is still in buffer FCD_RF0_Wait_For_SDI(); //Wait for SDI Input FC_CAL_Bit_High(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Chip select high, end transmission MX_RF_Mode = 0; FCD_RF0_Activate_RX_Mode(); //Switch to receive mode } } MX_UINT8 FCD_RF0_Check_Buffer(MX_UINT8 Timeout) { MX_UINT8 ByteRx, Data; MX_UINT8 LoopCount; MX_UINT8 Ptr = 0; MX_UINT8 NextByte = 1; MX_UINT8 Count; MX_UINT8 retVal = 255; //Nothing Received MX_UINT8 bCount = 0; MX_UINT8 Csum = 0; /* Return values 255 = No data 254 = Count error (data count > buffer) 253 = Insufficient data/timeout during reception 252 = Checksum error */ if (MX_RF_Mode != 0) //If we are in transmit mode { MX_RF_Mode = 0; FCD_RF0_Activate_RX_Mode(); //Switch to receive mode } //Get data count LoopCount = 0; ByteRx = 0; while((LoopCount < Timeout) && (ByteRx == 0)) { FC_CAL_Bit_Low(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Clear Chip Select bit delay_us(1); ByteRx = FC_CAL_Bit_In(RF_2_MX_RF_SDI_PORT, RF_2_MX_RF_SDI_PIN); FC_CAL_Bit_High(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Set Chip Select bit if (ByteRx == 0) delay_us(100); LoopCount++; } if(ByteRx) { retVal = 254; // Count received but nothing else FC_CAL_Bit_Low(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 0 delay_us(1); Count = RF_2_SPI_Master_Byte(0); FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 1 if (Count <= MX_RF_BUFFER_MAX) { retVal = 253; // Count and some data received but packet incomplete MX_RF_RX_Buff1[Ptr++] = Count; Count = Count + 2; //Include count and checksum while(NextByte) { LoopCount = 0; ByteRx = 0; while((LoopCount < Timeout) && (ByteRx == 0)) { FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 1 delay_us(1); FC_CAL_Bit_Low(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Clear Chip Select bit delay_us(1); ByteRx = FC_CAL_Bit_In(RF_2_MX_RF_SDI_PORT, RF_2_MX_RF_SDI_PIN); FC_CAL_Bit_High(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Set Chip Select bit if (ByteRx == 0) { delay_us(100); } LoopCount = LoopCount + 1; } if(ByteRx) { FC_CAL_Bit_Low(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 0 delay_us(1); MX_RF_RX_Buff1[Ptr++] = RF_2_SPI_Master_Byte(0); bCount = 0; } else { bCount = bCount + 1; if (bCount == 100) NextByte = 0; } if(Ptr == Count) { NextByte = 0; for(Ptr = 0; Ptr < (Count - 1); Ptr++) { MX_RF_RX_Buffer[Ptr] = MX_RF_RX_Buff1[Ptr]; Csum ^= MX_RF_RX_Buffer[Ptr]; } if (Csum == MX_RF_RX_Buff1[Ptr]) //Is checksum ok? retVal = Count - 2; else { MX_RF_RX_Buffer[1] = Csum; retVal = 252; //Count and packet data received but checksum error } } } } //FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 1 //SPI_Command(PMCREG); //SPI_Command(GENCREG); //SPI_Command(GENCREG | 0x0040); //SPI_Command(PMCREG | 0x0080); FCD_RF0_SPI_Command(FIFORSTREG); FCD_RF0_SPI_Command(FIFORSTREG | MX_RF_EXTID | 0x0002); // reset FIFO } FC_CAL_Bit_High(RF_2_MX_RF_FSEL_PORT, RF_2_MX_RF_FSEL_PIN); // FSEL Output 1 FC_CAL_Bit_High(RF_2_MX_RF_CS_PORT, RF_2_MX_RF_CS_PIN); // Chip select high, end transmission return (retVal); } MX_UINT8 FCD_RF0_Get_Data_Count() { return(MX_RF_RX_Buffer[0]); } MX_UINT8 FCD_RF0_Get_Buffer_Data(MX_UINT8 Index) { if (Index < MX_RF_BUFFER_MAX) return(MX_RF_RX_Buffer[Index + 1]); else return(0); } //LCDDisplay(0): //Makro-Implementierungen void FCD_LCDDisplay0_RawSend(MX_UINT8 in, MX_UINT8 mask) { MX_UINT8 pt; FC_CAL_Bit_Low(LCD_3__PORT0, LCD_3__BIT0); FC_CAL_Bit_Low(LCD_3__PORT1, LCD_3__BIT1); FC_CAL_Bit_Low(LCD_3__PORT2, LCD_3__BIT2); FC_CAL_Bit_Low(LCD_3__PORT3, LCD_3__BIT3); FC_CAL_Bit_Low(LCD_3__PORT4, LCD_3__RS); FC_CAL_Bit_Low(LCD_3__PORT5, LCD_3__E); pt = ((in >> 4) & 0x0f); if (pt & 0x01) FC_CAL_Bit_High(LCD_3__PORT0, LCD_3__BIT0); if (pt & 0x02) FC_CAL_Bit_High(LCD_3__PORT1, LCD_3__BIT1); if (pt & 0x04) FC_CAL_Bit_High(LCD_3__PORT2, LCD_3__BIT2); if (pt & 0x08) FC_CAL_Bit_High(LCD_3__PORT3, LCD_3__BIT3); if (mask) FC_CAL_Bit_High(LCD_3__PORT4, LCD_3__RS); LCD_3__DELAY; FC_CAL_Bit_High (LCD_3__PORT5, LCD_3__E); LCD_3__DELAY; FC_CAL_Bit_Low (LCD_3__PORT5, LCD_3__E); pt = (in & 0x0f); LCD_3__DELAY; FC_CAL_Bit_Low(LCD_3__PORT0, LCD_3__BIT0); FC_CAL_Bit_Low(LCD_3__PORT1, LCD_3__BIT1); FC_CAL_Bit_Low(LCD_3__PORT2, LCD_3__BIT2); FC_CAL_Bit_Low(LCD_3__PORT3, LCD_3__BIT3); FC_CAL_Bit_Low(LCD_3__PORT4, LCD_3__RS); FC_CAL_Bit_Low(LCD_3__PORT5, LCD_3__E); if (pt & 0x01) FC_CAL_Bit_High(LCD_3__PORT0, LCD_3__BIT0); if (pt & 0x02) FC_CAL_Bit_High(LCD_3__PORT1, LCD_3__BIT1); if (pt & 0x04) FC_CAL_Bit_High(LCD_3__PORT2, LCD_3__BIT2); if (pt & 0x08) FC_CAL_Bit_High(LCD_3__PORT3, LCD_3__BIT3); if (mask) FC_CAL_Bit_High(LCD_3__PORT4, LCD_3__RS); LCD_3__DELAY; FC_CAL_Bit_High (LCD_3__PORT5, LCD_3__E); LCD_3__DELAY; FC_CAL_Bit_Low (LCD_3__PORT5, LCD_3__E); LCD_3__DELAY; } void FCD_LCDDisplay0_Start() { FC_CAL_Bit_Low_DDR(LCD_3__PORT0, LCD_3__TRIS0, LCD_3__BIT0); FC_CAL_Bit_Low_DDR(LCD_3__PORT1, LCD_3__TRIS1, LCD_3__BIT1); FC_CAL_Bit_Low_DDR(LCD_3__PORT2, LCD_3__TRIS2, LCD_3__BIT2); FC_CAL_Bit_Low_DDR(LCD_3__PORT3, LCD_3__TRIS3, LCD_3__BIT3); FC_CAL_Bit_Low_DDR(LCD_3__PORT4, LCD_3__TRIS4, LCD_3__RS); FC_CAL_Bit_Low_DDR(LCD_3__PORT5, LCD_3__TRIS5, LCD_3__E); Wdt_Delay_Ms(12); FCD_LCDDisplay0_RawSend(0x33, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x33, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x32, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x2c, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x06, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x0c, 0); Wdt_Delay_Ms(2); //clear the display FCD_LCDDisplay0_RawSend(0x01, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x02, 0); Wdt_Delay_Ms(2); } void FCD_LCDDisplay0_Clear() { FCD_LCDDisplay0_RawSend(0x01, 0); Wdt_Delay_Ms(2); FCD_LCDDisplay0_RawSend(0x02, 0); Wdt_Delay_Ms(2); } void FCD_LCDDisplay0_PrintASCII(MX_UINT8 Character) { FCD_LCDDisplay0_RawSend(Character, 0x10); } void FCD_LCDDisplay0_Command(MX_UINT8 in) { FCD_LCDDisplay0_RawSend(in, 0); Wdt_Delay_Ms(2); } void FCD_LCDDisplay0_Cursor(MX_UINT8 x, MX_UINT8 y) { #if (LCD_3__ROWCNT == 1) y=0x80; #endif #if (LCD_3__ROWCNT == 2) if (y==0) y=0x80; else y=0xc0; #endif #if (LCD_3__ROWCNT == 4) if (y==0) y=0x80; else if (y==1) y=0xc0; #if (LCD_3__COLCNT == 16) else if (y==2) y=0x90; else y=0xd0; #endif #if (LCD_3__COLCNT == 20) else if (y==2) y=0x94; else y=0xd4; #endif #endif FCD_LCDDisplay0_RawSend(y+x, 0); Wdt_Delay_Ms(2); } void FCD_LCDDisplay0_PrintNumber(MX_SINT16 Number) { MX_SINT16 tmp_int; MX_UINT8 tmp_byte; if (Number < 0) { FCD_LCDDisplay0_RawSend('-', 0x10); Number = 0 - Number; } tmp_int = Number; if (Number >= 10000) { tmp_byte = tmp_int / 10000; FCD_LCDDisplay0_RawSend('0' + tmp_byte, 0x10); while (tmp_byte > 0) { tmp_int = tmp_int - 10000; tmp_byte--; } } if (Number >= 1000) { tmp_byte = tmp_int / 1000; FCD_LCDDisplay0_RawSend('0' + tmp_byte, 0x10); while (tmp_byte > 0) { tmp_int = tmp_int - 1000; tmp_byte--; } } if (Number >= 100) { tmp_byte = tmp_int / 100; FCD_LCDDisplay0_RawSend('0' + tmp_byte, 0x10); while (tmp_byte > 0) { tmp_int = tmp_int - 100; tmp_byte--; } } if (Number >= 10) { tmp_byte = tmp_int / 10; FCD_LCDDisplay0_RawSend('0' + tmp_byte, 0x10); while (tmp_byte > 0) { tmp_int = tmp_int - 10; tmp_byte--; } } FCD_LCDDisplay0_RawSend('0' + tmp_int, 0x10); } void FCD_LCDDisplay0_PrintString(MX_STRING String, MX_UINT8 MSZ_String) { MX_UINT8 idx = 0; for (idx=0; idx C3 trisc = trisc & 0xF7; if ((1)) portc = (portc & 0xF7) | 0x08; else portc = portc & 0xF7; break; } case 2: { //Output //Output: 1 -> C0 trisc = trisc & 0xFE; if ((1)) portc = (portc & 0xFE) | 0x01; else portc = portc & 0xFE; break; } case 3: { //Output //Output: 1 -> C2 trisc = trisc & 0xFB; if ((1)) portc = (portc & 0xFB) | 0x04; else portc = portc & 0xFB; break; } case 4: { //Output //Output: 1 -> C1 trisc = trisc & 0xFD; if ((1)) portc = (portc & 0xFD) | 0x02; else portc = portc & 0xFD; break; } default: { //Berechnung //Berechnung: // Stoerung = 1 FCV_STOERUNG = 1; //Gehe zum Verbindungspunkt //Gehe zum Verbindungspunkt: [A]: A goto FCC_Show_A; } } //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: PrintString(Abteilung_Text) FCD_LCDDisplay0_PrintString(FCV_ABTEILUNG_TEXT, FCSZ_ABTEILUNG_TEXT); //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: Cursor(0, 1) FCD_LCDDisplay0_Cursor(0, 1); //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: PrintString(Person) FCD_LCDDisplay0_PrintString(FCV_PERSON, FCSZ_PERSON); //Verbindungspunkt //Verbindungspunkt: [A]: A FCC_Show_A: ; } //Piepton zur Aufmerksamkeitserzeugung void FCM_Buzzer() { //Output //Output: 1 -> C4 trisc = trisc & 0xEF; if ((1)) portc = (portc & 0xEF) | 0x10; else portc = portc & 0xEF; //Schleife //Schleife: Schleife 10 Mal for (FCLV_LOOP1=0; FCLV_LOOP1<10; FCLV_LOOP1++) { //Warten //Warten: 200 ms Wdt_Delay_Ms(200); //Output //Output: 0 -> C4 trisc = trisc & 0xEF; if ((0)) portc = (portc & 0xEF) | 0x10; else portc = portc & 0xEF; //Warten //Warten: 100 ms Wdt_Delay_Ms(100); //Output //Output: 1 -> C4 trisc = trisc & 0xEF; if ((1)) portc = (portc & 0xEF) | 0x10; else portc = portc & 0xEF; } //Output //Output: 0 -> C4 trisc = trisc & 0xEF; if ((0)) portc = (portc & 0xEF) | 0x10; else portc = portc & 0xEF; } void FCM_Error() { //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: Uninit_RF_Module() FCD_RF0_Uninit_RF_Module(); //Set All Variables to Zero //Berechnung: // Abteilung = 0 // Taster = 0 // RF_BYTE_READ = 0 // Stoerung = 0 FCV_ABTEILUNG = 0; FCV_TASTER = 0; FCV_RF_BYTE_READ = 0; FCV_STOERUNG = 0; //Set String to Blank //Berechnung: // Abteilung_Text = " " FCI_SCOPY(" ",1, FCV_ABTEILUNG_TEXT,FCSZ_ABTEILUNG_TEXT); //Output //Output: 0 -> PORTC trisc = trisc & 0xF0; portc = (portc & 0xF0) | ((0) & 0x0F); //Warten //Warten: 250 ms Wdt_Delay_Ms(250); //Init RF Module //Aufruf Komponenten-Makro: Init_RF_Module() FCD_RF0_Init_RF_Module(); } void main() { //Initialisierung ansel = 0; anselh = 0; //Interrupt-Initialisierungs-Code option_reg = 0xC0; //C-Kode //C-Code: /* Bit 7 reserved set to 0 Bit 6-4 IRCF Set Oscillator to internal at 4MHZ 110 Bit 3 OSTS running from internal system clock Bit 2 HFINTOSC frequency is stable Bit 1 LFINTOSC LFINTOSC is stable Bit 0 SCS System Clock select Bit 1= internal OSC Next step is osctune Bit 7-5 don´t care Bit 4-0 01111 = Maximum freq 00000 = factory default 10000 Minimum freq osccon = 0b01100111; osctune = 0b00000010; */ osccon = 0x61; //Kommentar: ///* //Bit 7 reserved set to 0 //Bit 6-4 IRCF Set Oscillator to internal at 4MHZ 110 //Bit 3 OSTS running from internal system clock //Bit 2 HFINTOSC frequency is stable //Bit 1 LFINTOSC LFINTOSC is stable //Bit 0 SCS System Clock select Bit 1= internal OSC //Next step is osctune //Bit 7-5 don´t care //Bit 4-0 01111 = Maximum freq 00000 = factory default 10000 Minimum freq //*/ //osccon = 0b01100111; //osctune = 0b00000010; //Warten //Warten: 100 ms Wdt_Delay_Ms(100); //Init All Variables //Berechnung: // RF_BYTE_READ = 0 // Stoerung = 0 // Abteilung = 0 // Taster = 0 FCV_RF_BYTE_READ = 0; FCV_STOERUNG = 0; FCV_ABTEILUNG = 0; FCV_TASTER = 0; //Init String //Berechnung: // Abteilung_Text = " " FCI_SCOPY(" ",1, FCV_ABTEILUNG_TEXT,FCSZ_ABTEILUNG_TEXT); //Init Display //Aufruf Komponenten-Makro: Start() FCD_LCDDisplay0_Start(); //Init RF Module //Aufruf Komponenten-Makro: Init_RF_Module() FCD_RF0_Init_RF_Module(); //Wait to End Initphase //Warten: 200 ms Wdt_Delay_Ms(200); //Clear the Display //Aufruf Komponenten-Makro: Clear() FCD_LCDDisplay0_Clear(); //Schleife //Schleife: While 1 while (1) { //Set All Variables to Zero //Berechnung: // Abteilung = 0 // Taster = 0 // RF_BYTE_READ = 0 // Stoerung = 0 FCV_ABTEILUNG = 0; FCV_TASTER = 0; FCV_RF_BYTE_READ = 0; FCV_STOERUNG = 0; //Set String to Blank //Berechnung: // Abteilung_Text = " " FCI_SCOPY(" ",1, FCV_ABTEILUNG_TEXT,FCSZ_ABTEILUNG_TEXT); //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: RF_BYTE_READ=Receive_Byte(250) FCV_RF_BYTE_READ = FCD_RF0_Receive_Byte(250); //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: Clear() FCD_LCDDisplay0_Clear(); //Makro-Aufruf //Makro-Aufruf: Split_Buffer() FCM_Split_Buffer(); //Entscheidung //Entscheidung: Stoerung = 1? if (FCV_STOERUNG == 1) { //Makro-Aufruf //Makro-Aufruf: Error() FCM_Error(); } else { //Makro-Aufruf //Makro-Aufruf: Show() FCM_Show(); //Makro-Aufruf //Makro-Aufruf: Buzzer() FCM_Buzzer(); //Warten //Warten: 120 s Wdt_Delay_S(120); //Aufruf Komponenten-Makro //Aufruf Komponenten-Makro: Clear() FCD_LCDDisplay0_Clear(); //Output //Output: 0 -> PORTC trisc = trisc & 0xF0; portc = (portc & 0xF0) | ((0) & 0x0F); } } mainendloop: goto mainendloop; } void MX_INTERRUPT_MACRO(void) { }