Matrix user forums

Thanks Bachman, English is not my main language either, but as you said, if you are smart enough, there is Google translator :mrgreen: . I am very familiar with this component but the GetDeviceCount function does not work the way I want it to. In fact the Match ROM function (55h) is missing. Yes, if...

Hello, Sorry to pull out an old post but I am facing the same problem. How to interrogate a DS18B20 probe on several connected according to its ROM address? (I know in advance the ROM address of my probes) It's still more professional than heating each probe to find out which is which! I searched an...

Hello Kersing,

Thank you for your answer. I'm going to change my way because I do not have enough knowledge on this subject.

I think many people have switched to version 8 but unfortunately, I currently can not afford to spend.

Best regards

Steve

when I load only the bootloader file, I can detect the chip with the program Tinybootloader + but as soon as I put my program with Flowcode, I can not detect the chip anymore.

No one to help me ???

thank you in advance
Steve

Hello everyone, I ask for your help because I can not find the mistake. I loaded a bootlader file (tinybootloader) to reprogram the chip by serial link when I send the code "6" = "54h". The program will reset correctly when the correct code is detected but I can not communicate w...

thank you so much, everything is ok

Hi everyone, I just received a new programming deck (EB-006-00-09). I installed mlaoder and made the change in the compiation options. Unfortunately, when I want to configure the chip, I have a mloader error message. Are the settings I entered correct? Another question, can I do real-time debugging ...

Hello,

the compilation runs in safe mode. I found the culprit who is the Malwarbytes program. I had to disable a protection layer but I can compile my program again in Flowcode.

Thank you for your help

Do I have to update Boostc ?

As well as windows 10 64bits. Same version Flowcode (30.01.2013). Yesterday everything worked very well and after the update of windows, nothing.

This is one of the first code I wrote several years ago. After 5 minutes, the compiler did not finish. I canceled manually

no, the firewall is intergrated with avast.

The C code is well transcribed. It's just the next step that goes around in circles without giving any error

hello Martin,

I disabled avast and windows defender. it does not change anything

No one had this problem ?

The problem is the same with Flowcode V6

Steve

Hi all,

Since the last update of Windows 10 (version 1803), the compiler HEX no longer stops. He never ends.

I uninstalled, reinstalled the program, no changes

What should I do ?

Steve

Hello Steve 001

Thank you for your help, in this way, the program runs properly and Flowcode is now upgraded

Thank you

Steve

I have uninstalled and installed again Flowcode but the last update will not install. 1.) Uninstall 2.) Resart PC 3.) Install Flowcode "5.4.0.0" 4.) Click on "Help", "see the updates" 5.) A file downloads : "FlowcodeV5-PICmicro.exe" (72.4Mb) 6.) Run the execut...

Hello everyone, Since the installation of Windows 10, I had to uninstall and reinstall Flowcode V5 for drivers problems. I reinstall Flowcode V5 and everything works fine but when I want to update the program, a new executable (FlowcodeV5-PICmicro.exe) is downloaded but the program never want to exe...

Hi Benji, I did not dare change the file type, but I did it anyway. I changed as a result : #ifdef MX_ADC_TYPE_23 MX_UINT8 * ansel_reg; //ANSEL register pointer void FC_CAL_Enable_ADC (MX_UINT8 Channel, MX_UINT8 Conv_Speed, MX_UINT8 Vref, MX_UINT8 T_Charge) { adcon1 = (Conv_Speed & 0x07) << 4; /...

Hi to all, I wished to measure voltage on a or some analog input voltage of the Pic. But I can not configure the FVR module. When VDD = 5V, the LED lights up well at 1.2 V. But when VDD is below the threshold is also different. Yet in the datasheet section 14.0, the voltage VDD must not change the t...

It's good, it works. I made a syntax error when the macro "capture" is called.

The problem is fixed and it works well as a pulse counter.

Yes, it must be a bad command. I can not find it. Precision, I use a 16F876A.

Steve

Hi all,

To begin to understand the function capture of the timer 1, I would at every rising edge on pin CCP1, my variable is incremented.

I will post the beginning of pragramme but never increment the counter.

Someone could help me.

Steve

hello,

Well, I got the PIC and I could program it. Everything is ok.

These errors occur when I change the type of PIC in an existing program.

Steve

Hello Martin,

Yes, I compiled and no errors.
I will order this type of PIC and test in real situations.

thank you