Matrix user forums

hi,
By cutting the power eb063 several seconds, it works again.

Choosing hardware bug.

Oscilloscope on the line shows the bug, I sent this mesure(macro init).
A+bruno

hi,
Your solution does not work(/64)
Catastrophe, I grilled a module with your solution, the module is dead
The connection is good, I do not understand !!!
choice chanel 1 bug
I put another module sofward,it works
bruno

hi,
no compilation problem but can not transfer the program error on link hard spi bruno

Hi,
There is a bug on the hard choice eb063 atmega324p chanel 1 does not work
Choice software it’s works very well.
bruno

hi,
I just tested the installation another PC, no problem ,this is my pc

hi,
I managed to work, I gave an old file and that's ok
bruno

hi,
I tested, it does not work !!!!

bruno

hi,
no, I'll test and tell you if it is ok.
bruno

hi,
I have uninstalled and then 6.1.3.2 flowcode
I passed in 6.1.0 it is ok *.hex
when I install the patch 6.1.3.2 does not work
bruno

hi,
it doesn't work
in .c no ok , in .hex no ok error =1
bruno

hi,
it works version 6.1.2
now it impossible to compile in hex avr
bruno

hi,
Urgent new version 6.1.3
Updated pwm flowcode 6.1.3
Bug compilation Avr

hi, This module works very well, see: http://tsin.langevin-la-seyne.fr/SIN/magic-door.html but the EB063 is relatively fragile, a student grilled me max 3002 on one of my modules, I'm looking for only the circuit without the wiz810 that it's intact. Or buy this piece? (module without WIZ810) Thank b...

Hello,
One idea: configuration registers changed
bruno

hi,
measured period T = 204μs and not T = 103μs
The frequency is fix for any value of PERIOD OVERFLOW
bruno

hi,
AND FOR THE TIMER 0 (channel 1 and 2)TIMER 2(channel 6 and 7) phase correct pwm mode.
F(Hz) = fclk_I/O / (N * 510) with no adjustments PERIOD OVERFLOW (only 255), delete this setting
thank you
bruno

hello,
There is a bug on the simulation timer 0 it is really too speed.
Can you reduce its speed.
in real, it works very well
thank you
bruno

hi,
I tested
thank you, it works very well
bruno

hi, display error PWM Avr ATMEGA 324P: 20 000 000 Hz clk/8 period register n=255 You forgot to divide by 2 the frequency reading the file avr_cal_pwm.c, you choose the mode: Phase and Frequency Correct PWM Mode fOCnxPFCPWM = fclk_I/O/(2 ⋅ N ⋅ TOP) F = 4.88 kHz Period = 204.8 microseconds can you cha...

hi,
ok, I just tested and now it works very well.
thank you
bruno

HI,
Getrfiduid-> port b: 134 ok.
ReadRFIDBlock (5,0)-> port b : not 134 ( not ok ).

No wiring problem (cts) for works with flowcode 4 avr
bruno

hi, I wrote "2012" in Section 5 with flowcode 4 on the card icode when reading I do not have 134(0x86) on port B icode each card gives me a different status code (never 134(0x86)), the macro blocks reading does not work. in flowcode 4 avr with the same program I read "2012" witho...

ok,

the same file flowcode 4 works very well on my cards,
program card reading icode
http://tsin.langevin-la-seyne.fr/SIN/se ... -rfid.html
bruno

FLOWCODE AVR 4 program works very well with atmega324p (icode).

Flowcode 6.1 AVR bug routines for reading and writing blocks (icode) , can you solve this problem
thank you.
BRUNO