Matrix user forums

Hi Folks, have been forced to install my FLOWCODE 5 onto a new laptop.

Could somebody please tell me how I can obtain a new activation code. I have the CD with Key numbers etc.

hanks Folks.......John

OK, appreciate help.

Will FLOWCODE 5 work on Windows 11 64 bit ?

Hello Bachman, thanks for taking the time to help me out. I will go through you post again so that I can understand it better.

Take care, stay safe and have a great Christmas.

Hi everyone. I want to teach myself how to use a microchip chip to drive LCD's and 7 Segment displays.

Can somebody suggest a chip that would be suitable for a beginner. Nothing to fancy, perhaps to build a counter or temperature sensor.

Thanks folks, take care and stay safe..........John

Thanks Benj.

Hello folks. I am interested in upgrading from FLOWCODE 5 to FLOWCODE 8.2. Would my old laptop with the following specs be able to run the program with no problems?

Thanks a lot.....John

Thanks benj, so in terms of my program, would you say I have correctly set this up or not?

Hi, the aim of this program is to sense a certain heat or temperature level with a 10K NTC thermistor and then turn on a fan IF the temperature heat level exceeds the set maximum set by the 10K potentiometer. I've got the circuit working but am wondering if it is best to "read as Voltage" ...

I was using a bread board with jumper leads.

Turns out one of the jumper leads was faulty. Could have kicked myself!!!Anyway, thanks for your time.

Take care.....John

Thanks Martin, all is good.Thanks for your patience and time.

Thanks very much.I'll try your suggestions out and let you know Tuesday.Thanks again.............John

Hi, have done a simple flowcode program just to flash a led on 1 pin It converts to C and HEX fine. When I come to download the program into the 12F683 MCU,Mikroprog programmer says it sees a 12F508 MCU instead of 12F683 as selected? I've attached the flow chart and the error message.Any help will b...

Hi Martin, I'm up and running. Thanks so very much for your patience and help on this. Take care....John

Ok, got mikroprog connected.Would you be kind enough to have a look at the settings for me and point out where i went wrong please.I have not made any changes to the program itself.

Thanks for your help again. John

Hi Martin, I think Ill wait for the mikroprog to arrive (now tuesday) and then start again .What do you think?

Still got error message of USB CABLE NOT CONNECTED.

Have attached the program for your perusal.Thanks again.

Hi Martin, deleted as you suggested and then re-installed off your link. Installation went well with no hitches. Have not tried to program chip with pickit 2 yet.Will give it a bash later and let you know

Thanks for your help on this one .I've heeded your advice and dropped the idea of the board. Ordered the Mikroprog so here goes........should be here some time tomorrow. Once again thanks so much for your help on this one. Take care...John

Thanks for that.I think I will order the mikroprog. What do you think about using this board to program different PIC's with the mikroprog?

https://uk.rs-online.com/web/p/processo ... s/7916381/

OK, so it looks this is what we discussed?

https://uk.rs-online.com/web/p/chip-pro ... s/7916347/

What else do I need to get up and running? Cheers....John

Thanks Martin, can you suggest a board to plug into the Mikroprog that will enable me to swap out different PIC controllers. So, just to make sure I understand, the mikroprog is compatable with Flowcode 5,6,7 and 8? May I also ask where you got yours from? Thanks

Hi Martin, I ask you this question because I can't seem to get an honest opinion from elsewhere. Please be assured I am not looking to appropriate blame for anything to anybody so feel free to cut out the pc stuff and let me have it. Any hassles are usually appropriated to my own level of incompeten...

Can only find something to do with flowcode on this path
HKEY_CURRENT_USER

> Software > a file with Flowcode v4, flowcode v5 and PPPv3

I assume this is the one you want me to delete? The whole file or just the v5 part?

Steady now my friend, dont spoil the friendship.Speak to you tomorrow.