Matrix user forums

Hello.
I am making a volt metter using 7 seg. and the macro for it. Using Basic, a can separate all digit from a number, for example. Number=123, then, a=1, b=2, c=3. Are there some tools or way to make it with flowcode?
Thank you.

Hello, i have installed the V3 of flowcode and y want to update it. i downloaded the last update and when i want to install,it put a message that say. windows installer can not install it beacouse do not find the program to be update, or this is for other version, etc, etc. What can i do?
Thank

Hi. I make a program with flowcode 2.0 and in simulation mode it work very well, but is not the same in my circuit. The program is an analog imput (GPO) that is all time reading it and a push botton, when i push a push botton (GP3) it stop reading and put 1 in GP1 for 2 second and 0 after this time,...

Hi Ben.
I forgot something, i am using v2.0

I need make operations with numbers more high than 255. How i can declare variable like dobble byte and, how i make operations where the result could be fractions, example, A = 10/6.
Thank you

Hello. How I can see how much instructions have been executed while i run the program steep by steep?

There is some screen where can i see the instructions that are being executed and the amount of which they have been executed?

Thank you.

Hello, i have the same problem and i dont have c code in my flow chart. Then, i check very carefully my flow chart and i don't see any problem. When i tray to compile, it put the following message. Flowcode was unable to compile the flowcharts C code due to the following errors: No compilation error...

Thak you for your response.
First, i conected a resistor of 10k, but was the same problem. Sed me your email for sending the program

I use very very frecuently time in microsecod and some time is dificult to me use loop or TMRO for it. Some time i use program with variable time from 5 microsecond to 500 microsecod or more. The timer just have time in milisecond and second. Will Matrix M. integrate in flowCode 3.1V microsecod time...

1- Line Power Regulator 3KW or +
2- Power Invert
3- Line Voltaje Protector (Hight and Low voltage)
4- Cut-off for battery charger

Hi, I am using PIC12F675 for de following program. In the port a i have LEDs in GP1, GP2, GP4, GP5, And GP0 is an analog imput. GP3 have a Push botton to 5v and a resistor 1k to negative. The program work like this. When a push the botton, it put 1 in GP3 them, the program read the analog imput and ...

I bought the v2.0 to end of July of the 2006, at this moment, matrix multimedia had announced the exit of version 3, but it was not available still. I do not apply free for the update?

Ramtec

ramtecrd@yahoo.com

Hello Steve.
I bought version 2.0, what I can do to obtain the version 3.0?
Thank you

Ramtec

Hi Steve. The timer have milisecond and second options, the new version could have microsecond optios?
Thank you
RAMTEC

Hi. Why some program work very well in flowcode but not is the same in the circuit. (the hardware of circuit is fine). Why when i configure the internal clok of Pic16f88 in 4 or 8MHZ, some times the Pins are in high impedance and the program donΒ΄t work when the clok is configured in 31250 HZ the pr...

For Nanowatt pic (Example, pic16f88) Adjust the Clock speed without using C code when you donΒ΄t have the developer board.

Thankyou Ian. Yes, i connected an resistor for prevent damage to the pic. The problem is that when i use the pin like input conecting a push botton, and leter, when i want use the same pin like output (using an output block in flowchat) it is not recognized until the push botton is conected to the p...

Hi, i want to know how i can use a pin that first has been configurate like in put (with push botton) in an out put (leter) without disconnecting the push botton using flowcode in the same flowchart.
Thank