Matrix user forums

Hello. Thanks for the Answer. It Works Great in Software and Hardware - Thanks

Hello. i have a Problem with Arduino Nano328 in Simulation. I want Toggle a Led with the Interrupt. The simple Programm works in Mega328, 16F877A but not in NANO328?!?!?! I try this only in simulation not in Hardware. Is this a BUG or is something wrong in the Arduino Programm?

Thanks for Help

After Christmas I will try the Pro compiler and you hear from me how it then works.

Thanks a lot Band marry christmas

It looks like better to change to the XC8 Pro Compiler.

With a 16F877A with 19.66Mhz always comes after a few seconds CRC Error

Hello. It Works great with 64MHz!!

With 18F46K22 with 64MHz it Workshops, BUT Minus degree Not work correct!

Hallo. Thanks for the fast replay. I use a 16F877A Witz 19.6608MHz. With pullup (10k) und Very short strips (10cm).
I Test it tomorrow with a 18F46K22 with 64MHz.
You hear from mehr.

And the Default Baud from the Nextion is 9600 you have 38400. https://www.itead.cc/wiki/Nextion_Instruction_Set, baud /Current value of baud /1.baud=2400 2.baud=4800 3.baud=9600

4.baud=19200 5.baud=38400 6.baud=57600 7.baud=115200

Do you already have a working nextion?
I describe my nextion as on the picture and the functioned.
First, I choose pointer (z0) - then the value what it should display (retval) and end the transmission with 3 times send of 255. I do not know whether it goes as you do (Slepp = 0 \ xff \ xff \ xff )

With the DHT11 is the Same. It jumps from 10 to 40 without CRC test. With CRC Test it comes CRC Error on thr Display.

Hello. Unfortunately it does not work. The error message "CRC Error" comes.
When I turn off the CRC test, I see a temperature And humidity but it is not correct and jumps around, from 100 to -100 everything is there. It is the same with the humidity.

Hallo benj.
There is already a solution with the
Component macro?
User jgu1 has the same problem!!

low contrast and high contrast

Hello. I Test the Programm on a PIC ( i dont have AVR Lizenz). I change the "Transparent", in the Component Macro, from 0 to 1 - look at the second Picture. Did you change the contrast higher? Is the display darker? You need a potentiometer between Vout (Pin 18) and GND (Pin 1) and the gri...

Hello. I have tried the example program of Flowcode Wiki but unfortunately the program does not run. I have tried a 16F877A with 19.9906MHz and tried an 18F46K22 with 64MHz, neither of the two running the program. It remains attached to "Sample Sensor". The output B6 becomes high, the B7 n...

Hello. Thank you for the link. After the installation it runs however not quite correctly. I change the LED controller to AP104 - it runs great. THANK YOU. @Benj: I found the scrolling RGB Message Board, from you. Can you post the Flowchart? I could learn a lot about text scroll ! https://www.youtub...

Hello. Thanke for the tip, the error is gone. The other error is still there, and the program does not work in the PIC. Does the WS2812 work with an 8-bit controller?

Hello.
Can you Help me with this Problem? I have a 18F46K22 with 64Mhz and have this Error.
I have a Flowcode 7 Pro Lizenz.

Hello. Do you have a solution on how to receive data from the display and evaluate? I want a motor on, but I can not figure out how I can receive data correctly. Does anyone have a solution? Data can I write correctly in the display. I wanted to register on the Russian Flowcode page but can not get ...

Hello. I have the same problem, there is already a solution?