Hello,
I add CDC USB Serial component in my customized component of FV5. This component use USART1 to drive the data from USB. But I can't find data on the USART1. I tried add RS232 Component only, don't work with the hardware mode, no data. Bad data in software mode. Have you update for the USART FV5 Component for ARM AT91SAM7S512 ?
Thank you for your answer.
USART Component don't work
Moderator: Benj
-
- Valued Contributor
- Posts: 779
- Joined: Fri Jun 06, 2014 3:53 pm
- Has thanked: 186 times
- Been thanked: 204 times
Re: USART Component don't work
Hi
You would need to attach your chart for people to assist in the issue.
However v5 is very, very old now and unsupported other than by the forum so specific updates are probably not a high priority. Have you considered upgrading to v10? It's free to use and all components are free too. The website will provide full details but it is worth considering.
Regards
You would need to attach your chart for people to assist in the issue.
However v5 is very, very old now and unsupported other than by the forum so specific updates are probably not a high priority. Have you considered upgrading to v10? It's free to use and all components are free too. The website will provide full details but it is worth considering.
Regards
- Nico595
- Posts: 84
- Joined: Mon Jan 23, 2012 6:46 pm
- Location: France
- Has thanked: 12 times
- Been thanked: 10 times
Re: USART Component don't work
Hi chipfryer,
Thank you for your fast answer.
I checked all defines in Board_Generic.h and AT91SAM512.h the last night, the CDC Serial driver code work fine with the UART1 today
You have right about the FC5, it's a old version but I can customize all FC5 Components and add my customized Components. I bought ARM FC6 Professional without use. I heard the FC10 version is now available with FC10 customized Components.
I don't understand why Matrix Flowcode Team upgrade the software and remove this function.
Now, if a member of the Flowcode Team replace my FC6 licence key by a FC10 licence key, I can use FC10 with the customized Components function as previous when I bought the FC6 version. If not I work with the FC5. It's always a very good version, probably the best for me. I don't need simulation and nice pictures with graphs to do my job.
Thank you again chipfryer,
Best,
Nicolas.
Thank you for your fast answer.
I checked all defines in Board_Generic.h and AT91SAM512.h the last night, the CDC Serial driver code work fine with the UART1 today
You have right about the FC5, it's a old version but I can customize all FC5 Components and add my customized Components. I bought ARM FC6 Professional without use. I heard the FC10 version is now available with FC10 customized Components.
I don't understand why Matrix Flowcode Team upgrade the software and remove this function.
Now, if a member of the Flowcode Team replace my FC6 licence key by a FC10 licence key, I can use FC10 with the customized Components function as previous when I bought the FC6 version. If not I work with the FC5. It's always a very good version, probably the best for me. I don't need simulation and nice pictures with graphs to do my job.
Thank you again chipfryer,
Best,
Nicolas.
-
- Valued Contributor
- Posts: 779
- Joined: Fri Jun 06, 2014 3:53 pm
- Has thanked: 186 times
- Been thanked: 204 times
Re: USART Component don't work
Hi
I have very fond memories of v5 as it's the first I really used to any extent.
In v10 the source code for components is made available too. This is quite a helpful feature. As v10 is free (for hobby use) you could always try it and see if it provides you with any benefit.
Regards
I have very fond memories of v5 as it's the first I really used to any extent.
In v10 the source code for components is made available too. This is quite a helpful feature. As v10 is free (for hobby use) you could always try it and see if it provides you with any benefit.
Regards