Raspberry Pi Chip Pack - Revision history

BenR at 10:56, 23 May 2018

2018-05-23T10:56:22Z

BenR at 10:56, 23 May 2018

2018-05-23T10:56:10Z

BenR at 15:03, 10 May 2018

2018-05-10T15:03:11Z

BenR at 14:13, 10 May 2018

2018-05-10T14:13:42Z

BenR at 13:59, 10 May 2018

2018-05-10T13:59:28Z

BenR at 13:58, 10 May 2018

2018-05-10T13:58:19Z

BenR at 13:57, 10 May 2018

2018-05-10T13:57:58Z

BenR: Created page with "Flowcode supports the Raspberry Pi range of hardware. Currently the Pi2 and Pi3 models are supported. Most components in Flowcode should work with the Raspberry Pi hardware a..."

2018-05-10T13:38:14Z

Created page with "Flowcode supports the Raspberry Pi range of hardware. Currently the Pi2 and Pi3 models are supported. Most components in Flowcode should work with the Raspberry Pi hardware a..."

New page

Flowcode supports the Raspberry Pi range of hardware. Currently the Pi2 and Pi3 models are supported.

Most components in Flowcode should work with the Raspberry Pi hardware as is allowing you to do a lot with the Raspberry Pi GPIO header.

Also built into Flowcode is a TCP/IP component allowing you to communicate via the Ethernet and Wifi network connections which vastly simplifies the job of creating IoT type applications.

With a RPI target selected the

An E-block 2 board is also available (BL0136) which provides Ghost Technology (ICD / ICT) debugging support.

@@ Line 15: / Line 15: @@
 A guide on getting started with the Raspberry Pi chip pack in Flowcode is available from the link below.
-[[https://www.matrixtsl.com/resources/files/misc/Using%20Raspberry%20Pi%20with%20Flowcode%208.pdf Raspberry Pi Quick Start Guide]]
+[https://www.matrixtsl.com/resources/files/misc/Using%20Raspberry%20Pi%20with%20Flowcode%208.pdf Raspberry Pi Quick Start Guide]
 An E-block 2 board is also available ([https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]) which provides Ghost Technology (ICD / ICT) debugging support. An E-blocks 1 compatible board is also available ([http://www.matrixtsl.com/webshop/raspberry-pi-expansion-module-with-cable.html EB380]).

@@ Line 15: / Line 15: @@
 A guide on getting started with the Raspberry Pi chip pack in Flowcode is available from the link below.
-[[XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX]]
+[[https://www.matrixtsl.com/resources/files/misc/Using%20Raspberry%20Pi%20with%20Flowcode%208.pdf Raspberry Pi Quick Start Guide]]
 An E-block 2 board is also available ([https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]) which provides Ghost Technology (ICD / ICT) debugging support. An E-blocks 1 compatible board is also available ([http://www.matrixtsl.com/webshop/raspberry-pi-expansion-module-with-cable.html EB380]).

← Older revision		Revision as of 15:03, 10 May 2018
Line 18:		Line 18:


−	An E-block 2 board is also available ([https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]) which provides Ghost Technology (ICD / ICT) debugging support.	+	An E-block 2 board is also available ([https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]) which provides Ghost Technology (ICD / ICT) debugging support. An E-blocks 1 compatible board is also available ([http://www.matrixtsl.com/webshop/raspberry-pi-expansion-module-with-cable.html EB380]).

← Older revision		Revision as of 14:13, 10 May 2018
Line 2:		Line 2:


−	Most components in Flowcode should work with the Raspberry Pi hardware as is allowing you to do a lot with the Raspberry Pi GPIO header.	+	Most components in Flowcode should work with the Raspberry Pi hardware as is allowing you to do a lot with the Raspberry Pi GPIO header. Supported peripherals include general purpose I/O, I2C, PWM, SPI and UART.

← Older revision		Revision as of 13:59, 10 May 2018
Line 18:		Line 18:


−	An E-block 2 board is also available ([[https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]]) which provides Ghost Technology (ICD / ICT) debugging support.	+	An E-block 2 board is also available ([https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]) which provides Ghost Technology (ICD / ICT) debugging support.

← Older revision		Revision as of 13:58, 10 May 2018
Line 18:		Line 18:


−	An E-block 2 board is also available ([[https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036\|BL0136]]) which provides Ghost Technology (ICD / ICT) debugging support.	+	An E-block 2 board is also available ([[https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036 BL0136]]) which provides Ghost Technology (ICD / ICT) debugging support.

@@ Line 1: / Line 1: @@
 Flowcode supports the Raspberry Pi range of hardware. Currently the Pi2 and Pi3 models are supported.
 Most components in Flowcode should work with the Raspberry Pi hardware as is allowing you to do a lot with the Raspberry Pi GPIO header.
 Also built into Flowcode is a TCP/IP component allowing you to communicate via the Ethernet and Wifi network connections which vastly simplifies the job of creating IoT type applications.
 With a RPI target selected the
-An E-block 2 board is also available (BL0136) which provides Ghost Technology (ICD / ICT) debugging support.
+An E-block 2 board is also available ([[https://www.matrixtsl.com/webshop/catalogsearch/result/index/?mode=grid&q=BL0036|BL0136]]) which provides Ghost Technology (ICD / ICT) debugging support.