Traffic Light 1-Way - Revision history

SteveT: removed bad link in Component Details

2026-03-04T12:36:30Z

removed bad link in Component Details

2019-10-01T11:06:53Z

2019-10-01T11:06:33Z

2019-10-01T11:05:34Z

2018-05-24T10:27:55Z

2018-04-27T14:49:17Z

2018-04-27T14:48:11Z

2018-04-20T14:24:00Z

2018-04-20T14:08:31Z

2018-04-20T14:08:10Z

← Older revision		Revision as of 12:36, 4 March 2026
Line 66:		Line 66:

	A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].		A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].
−
−	~~{{Fcfile2\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}~~

← Older revision		Revision as of 11:06, 1 October 2019
Line 67:		Line 67:
	A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].		A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].

−	{{~~Fcfile~~\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}	+	{{Fcfile2\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}

← Older revision		Revision as of 11:06, 1 October 2019
Line 67:		Line 67:
	A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].		A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].

−	{{~~Fcfile2~~\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}	+	{{Fcfile\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}

← Older revision		Revision as of 11:05, 1 October 2019
Line 66:		Line 66:

	A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].		A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].
		+
		+	{{Fcfile2\|TrafficLight1-WayWorksheet1.fcfx\|Traffic Light 1-Way - Worksheet 1}}

← Older revision		Revision as of 10:27, 24 May 2018
Line 61:		Line 61:

	Add a call to the GetStopGo function and assign the return value to a LED to indicate if it is safe to go through the light or not.		Add a call to the GetStopGo function and assign the return value to a LED to indicate if it is safe to go through the light or not.
		+
		+
		+	==Component Details==
		+
		+	A full listing of the macros and properties available in this component are available from the [[Component:_ID_0c6b22fc_6e81_4406_aabd_5feb928e6aee\|Components Section]].

@@ Line 55: / Line 55: @@
 * Add component macro calls in your loop to call the SetLightState component macro, add one for each state.
 * Add delay icons between the component macros to recreate the automatic mode flow and transition timings.
-* Can you think of reasons why this way of coding is better than in Exercise 2?
+* Can you think of reasons why this way of coding is better or worse than in Exercise 2?

@@ Line 16: / Line 16: @@
 * Add the ‘Traffic Light 1-Way’ component to the 3D Panel, from the ’Simulation -> Scenarios’ category.
 * Adjust the 3D Panel so that you can see the traffic light, The [[PresetViews|Preset Views]] button or clicking the arrows at the top left of the 3D Panel window can be very helpful.
 * Add a loop to your program to loop forever until the simulation stop button is pressed.
-* Use the component macro ‘AutomaticMode’ to start the lights moving through its pre-programmed light patterns.
+* Run the simulation by clicking the Play button on the top toolbar.
-* Start the simulation running and take note of the different states the lights can be in.
+* Take note of the different states the lights can be in.

@@ Line 18: / Line 18: @@
 * Add a loop to your program to loop forever until the simulation stop button is pressed.
 * Use the component macro ‘AutomaticMode’ to start the lights moving through its pre-programmed light patterns.
-* Start the simulation running and count the different states the lights can be in.
+* Start the simulation running and take note of the different states the lights can be in.
@@ Line 28: / Line 28: @@
 [[File:TL2.jpg]]

@@ Line 15: / Line 15: @@
 * Create a new flowchart, and select ‘No chip’ as the target device. We choose no chip as this is a simulation only exercise.
 * Add the ‘Traffic Light 1-Way’ component to the 3D Panel, from the ’Simulation -> Scenarios’ category.
-* Adjust the 3D Panel so that you can see the traffic light, The [PresetViews|Preset Views] button or clicking the arrows at the top left of the window can be very helpful.
+* Adjust the 3D Panel so that you can see the traffic light, The [[PresetViews|Preset Views]] button or clicking the arrows at the top left of the window can be very helpful.
 * Add a loop to your program to loop forever until the simulation stop button is pressed.
 * Use the component macro ‘AutomaticMode’ to start the lights moving through its pre-programmed light patterns.