Component: Infrared Array AMG88xx (Light)

Author	Matrix TSL
Version	1.0
Category	Light

Infrared Array AMG88xx component

An 8x8 (64) Pixel infrared sensor array allowing basic none contact temperature detection.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	SetMovingAverageMode
Set the moving average mode on or off.
[[File:]] -	Mode
0 = Off, 1 = On
- VOID	Return

	ClearInterrupt
Clear any triggered interrupts
- VOID	Return

	SetInterruptMode
Set the interrupt to either absolute value or difference mode
[[File:]] -	Mode
0 = Difference / 1 = Absolute
- VOID	Return

	SetInterrupt
Allows the interrupt pin to be enabled or disabled.
[[File:]] -	Mode
0 = Disabled / 1 = Enabled
- VOID	Return

	SetInterruptLevels
Set the interrupt levels. Interrupt when going above High or interrupt when going below Low.
[[File:]] -	High
Range: -1023 to 1023
[[File:]] -	Low
Range: -1023 to 1023
[[File:]] -	Hysteresis
Range: -1023 to 1023 ( Recommend 0.95 * High )
- VOID	Return

	SamplePixels
Reads Infrared sensor values
- VOID	Return

	ReadThermistor
Reads the onboard thermistor Returns the temperature in degrees Celsius as a floating point value
[[File:]] -	Return

	ReadPixel
Reads the temperature of a single pixel value from the last SamplePixels call.
- BYTE	Index
Pixel to read. Range: 0 - 63
[[File:]] -	Return

	Initialise
Sets up the I2C interface and initialises the sensor.
- VOID	Return

	I2CTransInit
Initialises the I2C Transaction mode with the 7-bit device address
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	DeviceAddress
7-bit Device Address
- BYTE	Baud
0=100KHz, 1=400KHz, 2=1MHz
- VOID	Return

	IOSetOutputPin
Sets the selected digital pin to an output and assigns the output state.
- BYTE	Pin
Range: 0-29
[[File:]] -	State
Range: 0-1
- VOID	Return

	UARTReceive
Receives a data byte from the UART. Recommend calling the UARTCheckRx function first to ensure data is available.
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Return

	SPIInitialise
Initialsie the SPI module ready for communications
- BYTE	Channel
Channel Index: Range 0 - SPI Bus Count - 1
- VOID	Return

	I2CSend
Transmit a byte using the I2C bus
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	DataOut
[[File:]] -	Return

	UARTSend
Send a byte via the UART module
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Data
Data Byte to send. Range: 0-255
- VOID	Return

	PWMSetPrescaler
Sets the prescaler for the PWM output
- BYTE	Channel
- BYTE	Prescaler
- BYTE	Period
- VOID	Return

	PWMEnable
Enable a PWM output
- BYTE	Channel
Range: 0-1
- VOID	Return

	Initialise
Initialise the comms to the Arduino board ready for commands to be sent.
- VOID	Return

	IOSetOutputPin
Sets the selected digital pin to an output and assigns the output state.
- BYTE	Pin
Range: 0-29
[[File:]] -	State
Range: 0-1
- VOID	Return

	UARTReceive
Receives a data byte from the UART. Recommend calling the UARTCheckRx function first to ensure data is available.
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Return

	ADCSampleAverage10
Reads the voltage present on an Analog pin as an 10-bit value range 0-1023. Performs the selected number of samples with the selected time in microseconds in between samples
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 100
- BYTE	SampleDelay
Delay in us between each sample
- UINT	Return

	OneWireScanBus
Scans the one wire bus to detect all connected devices. Returns the number of one wire devices found.
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	SPIInitialise
Initialsie the SPI module ready for communications
- BYTE	Channel
Channel Index: Range 0 - SPI Bus Count - 1
- VOID	Return

	OneWireReceiveByte
Receives a byte from the one wire bus a bit at a time
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	I2CSend
Transmit a byte using the I2C bus
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	DataOut
[[File:]] -	Return

	UARTSend
Send a byte via the UART module
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Data
Data Byte to send. Range: 0-255
- VOID	Return

	OneWireGetDeviceCount
Returns the number of devices found by the last ScanBus operation.
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	PWMSetPrescaler
Sets the prescaler for the PWM output
- BYTE	Channel
Range: 0 - 11
- BYTE	Prescaler
- BYTE	Period
- VOID	Return

	PWMEnable
Enable a PWM output
- BYTE	Channel
Range: 0-11
- VOID	Return

	ADCSampleArray10
Reads the voltage present on an Analog pin as an 10-bit value range 0-1023 Performs the selected number of samples with the selected time in microseconds in between samples and returns each sample in a single packet
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 32
- UINT	SampleDelay
Delay in us between each sample
- UINT	Samples
10-bit samples returned from the function
- VOID	Return

	ADCSampleAverage8
Reads the voltage present on an Analog pin as an 8-bit value range 0-255 Performs the selected number of samples with the selected time in microseconds in between samples
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 100
- BYTE	SampleDelay
Delay in us between each sample
- BYTE	Return

	Initialise
Initialise the comms to the Arduino board ready for commands to be sent.
- VOID	Return

Property reference

	Properties
	Connections
	Address
	Channel
Channel selection
	SDA
Pin used for SDA (data signal)
	SCL
Pin used for SCL (clock signal)
	Baud Select
Baud rate option selector
	Baud Rate
Baud rate to be used
	Stop Delay
On older microcontroller devices there is a potential for the I2C hardware channel to lock up if there is not a 10ms delay between an I2C stop event and the next I2C start event. Most modern microcontrollers will not have a problem so this property can be disabled to speed up the I2C communications.
	Simulations
	Scope Traces
Selects if the scope traces are automatically generated or not
	Console Data
Selects if the console data is automatically generated or not
	API