Component: Light Sensor (Grove 101020132) (101020132) (Light)

Author	Matrix Ltd
Version	1.0
Category	Light

Light Sensor (Grove 101020132) component

The Light sensor module is a simple analogue photo transistor. Used to detect the intensity of the indoor light.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	GetString
Reads the ADC as a direct voltage and returns as as tring
- STRING	Return

	GetAverageByte
Function call to read the ADC as a byte average sample over time
- BYTE	NumSamples
- BYTE	DelayUs
Number of micro seconds in between taking each sample
- BYTE	Return

	GetAverageInt
Function call to read the ADC as a full width average sample over time
- BYTE	NumSamples
- BYTE	DelayUs
Number of micro seconds in between taking each sample
- UINT	Return

	GetVoltage
Reads the ADC as a direct voltage
[[File:]] -	Return

	GetInt
Blocking call to read the ADC at full bit depth
- UINT	Return

	GetByte
Blocking call to read the ADC as a byte
- BYTE	Return

	Initialise
Initialise the sensor configuration as set by the component properties. Sets the default intigration time and gain as well as enable the sensor.
- VOID	Return

	Initialise
Configures the I2C peripheral and puts the sensor into one shot mode ready to be sampled. Must be called before calling any of the other component macros. Returns 1 if the sensor has been intialised correctly, else returns 0.
- BYTE	Return

	Initialise
Starts up the I2C bus and initialises the pressure sensor ready for use. Returns 1 for a sucessful startup. Returns 0 for a failed startup or no device detected.
- BYTE	Return

	Initialise
Sets up the GSM module. Returns 0 for OK, 255 for no reply and 254 for command fail.
- BYTE	Return

	SampleAccel
Samples the accelerometer 0 = no new data, 1 = new data available
- BYTE	Return

	Left
Rotates the robot left - waits for the angle to be traversed before returning
- UINT	Angle
Angle to turn in degrees
- VOID	Return

	ReadIR
Reads an IR sensor 0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- BYTE	index
0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- UINT	Return

	LCDDrawPixel
Allows a single pixel on the LCD to be set or cleared
- BYTE	X
X Pixel 0-127
- BYTE	Y
Y Pixel 0-31
- BYTE	State
0=White (Off), 1=Black (On)
- VOID	Return

	ServoSetPosition
Allows one of the servo positions to be assigned
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	CardBitmap
Displays a monochrome bitmap read from the card on the LCD
- BYTE	X
Range 0-127
- BYTE	Y
Range 0-31
- STRING	Filename
- BYTE	Return

	CardRecordMic
Records an audio stream on the card from the microphone
- BYTE	BitDepth
0=8-bit, 1=16-bit
- BYTE	SampleRate
Sample Rate 0=8KHz, 1=16KHz
- UINT	RecordTime
Time to record for in seconds, Range 0-65535
- STRING	Filename
- BYTE	Return

	CardOpen
Attempts to open an existing file on the SD card 255=Error, 1=File not found, 0=Open OK
- STRING	Filename
- BYTE	Return

	Forwards
Drives the robot forwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	ReadBearing
Reads the compass bearing based on the degrees clockwise from magnetic north.
[[File:]] -	Return

	GetConsoleHandle
Gets the handle to the console allowing data displaying on the panel etc.
[[File:]] -	Return

	LCDDrawLine
Allows a single pixel width line to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ServoAutoMoveToPosition
Allows one of the servo positions to move gradually to a new position
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	ReadAllValue
Reads a single value stored from the read all command Index dictates which sensor value to read
- BYTE	Index
0=SW, 1-8=IR, 9-10=Line, 11=Light, 12=Mic, 13-15=Accel
- UINT	Return

	LCDBacklight
Allows the LCD backlight brighntess to be adjusted
- BYTE	Intensity
Range 0-100, 0=Off, 1=Min Brightness, 100=Max Brightness
- VOID	Return

	LCDDrawRect
Allows a rectangle to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ReadLine
Reads one of the IR line sensors 0-1 0=Left, 1=Right
- BYTE	index
0=Left, 1=Right
- UINT	Return

	ServoDisable
Allows one of the servo outputs 0-3 to be disabled
- BYTE	Channel
Range 0-3
- VOID	Return

	ServoEnable
Allows one of the servo outputs 0-3 to be enabled
- BYTE	Channel
Range 0-3
- VOID	Return

	CardReadByte
Reads a byte from the currently open file. Starts at the beginning of the file and auto increments to the end
- BYTE	Return

	CardErase
Attempts to delete an existing file on the SD card 255=Error, 1=File not found, 0=Delete OK
- STRING	Filename
- BYTE	Return

	CardWriteByte
Appends a byte to the end of the currently open file
- BYTE	Data
- VOID	Return

	EncoderRead
Reads one of the motor encoder counters. Approx 0.328296mm of travel per encoder unit.
- BYTE	index
0=Left, 1=Right
- UINT	Return

	SetMotors
Sets the motor speeds without feedback Range -100 to 100
[[File:]] -	Left
Range -100 to 100
[[File:]] -	Right
Range -100 to 100
- VOID	Return

	Backwards
Drives the robot backwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	EncoderReset
Resets the motor encoder counters
- VOID	Return

	LCDVerbose
Allows the LCD to automatically report the API commands as they get processed. Default - verbose on
- BYTE	State
0=Off 1=On
- VOID	Return

	SetProp
Allows the COM port property to be set from a parent component.
- STRING	PropName
- ULONG	PropVal
- VOID	Return

	CardInit
Attempts to startup the SD card 255=No Card, 254=Init Fail, 0=Init OK
- BYTE	Return

	GetProp
Allows the property filter for the COM port list to be copied to a parent component.
- STRING	PropName
- STRING	Return

	LCDClear
Clears the LCD
- VOID	Return

Property reference

	Properties
	VRef voltage
Used by the GetVoltage or GetString component macros to take an ADC reading and convert it into a Voltage. +VRef voltage x 10mV Default 500 = 5.0V
	VRef option
Defines what is used as the ADC maximum reference. ADC Range = GND to VRef Voltage. VDD - Defines the microcontrollers power supply pin as the max reference, VREF+ Pin - Dedicated pin on the microcontroller to allow for a variable reference voltage.
	Conversion speed
Clock setting to select how fast the ADC peripheral will perform an ADC conversion. The FRC setting is based on a RC time base and so will vary with temperature and pressure. Other settings are generally based on divisions of the master clock.
	Aquisition cycles
Number of micro seconds to wait for the ACD input to charge before starting the analogue sample.
	Bit Depth
Maximum number of digital bits the ADC can sample. 8 bit = ADC range 0 - 255 10 bit = ADC range 0 - 1023 12 bit = ADC range 0 - 4095
	Connections
	Channel
Analogue input channel - which pin is the analogue input conected to?
	Simulations
	Scope Traces
Selects if the scope traces are automatically generated or not