Component: Injector (AT) (Test Injectors)

Author	Matrix Ltd
Version	1.1
Category	Test Injectors

Injector (AT) component

Comms data injector to replicate basic AT command syntax. The component will record each incoming character until the termination character is received. Once this happens the component will respond by echoing back the received data followed by an "OK" reply.

Detailed description

No detailed description exists yet for this component

Examples

GSM Example File GSM Example Example should show the following on the display on the panel and on the hardware.

The AT injector component allows us to simulate the response of the GSM module.

Downloadable macro reference

	UARTBaud
- BYTE	Channel
- BYTE	Rate
- VOID	Return

	UARTCheckRX
- BYTE	Channel
- BYTE	Return

	UARTInitialise
- BYTE	Channel
- VOID	Return

	GetConsoleHandle
Gets the handle to the console allowing data displaying on the panel etc.
[[File:]] -	Return

	UARTReceive
- BYTE	Channel
- BYTE	Return

	UARTSend
- BYTE	Channel
- BYTE	Data
- VOID	Return

	GetInt
Gets an integer from the LUT
- ULONG	Index
- ULONG	Return

	SetFloatBits
Sets the size of a float LUT entry
- BYTE	Bits
- VOID	Return

	AddInt
Int to add to the int array
- ULONG	Value
Int to add to the int array
- VOID	Return

	AddFloat
Add a float to the floating point LUT
[[File:]] -	Value
Floating point values
- VOID	Return

	Initialise
Sets up the GSM module. Returns 0 for OK, 255 for no reply and 254 for command fail.
- BYTE	Return

	SampleAccel
Samples the accelerometer 0 = no new data, 1 = new data available
- BYTE	Return

	Left
Rotates the robot left - waits for the angle to be traversed before returning
- UINT	Angle
Angle to turn in degrees
- VOID	Return

	ReadIR
Reads an IR sensor 0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- BYTE	index
0=Left, 1=FrontLeft, 2=Front, 3=FrontRight, 4=Right, 5=RearRight, 6=Rear, 7=RearLeft
- UINT	Return

	LCDDrawPixel
Allows a single pixel on the LCD to be set or cleared
- BYTE	X
X Pixel 0-127
- BYTE	Y
Y Pixel 0-31
- BYTE	State
0=White (Off), 1=Black (On)
- VOID	Return

	ServoSetPosition
Allows one of the servo positions to be assigned
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	CardBitmap
Displays a monochrome bitmap read from the card on the LCD
- BYTE	X
Range 0-127
- BYTE	Y
Range 0-31
- STRING	Filename
- BYTE	Return

	CardRecordMic
Records an audio stream on the card from the microphone
- BYTE	BitDepth
0=8-bit, 1=16-bit
- BYTE	SampleRate
Sample Rate 0=8KHz, 1=16KHz
- UINT	RecordTime
Time to record for in seconds, Range 0-65535
- STRING	Filename
- BYTE	Return

	CardOpen
Attempts to open an existing file on the SD card 255=Error, 1=File not found, 0=Open OK
- STRING	Filename
- BYTE	Return

	Forwards
Drives the robot forwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	ReadBearing
Reads the compass bearing based on the degrees clockwise from magnetic north.
[[File:]] -	Return

	GetConsoleHandle
Gets the handle to the console allowing data displaying on the panel etc.
[[File:]] -	Return

	LCDDrawLine
Allows a single pixel width line to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ServoAutoMoveToPosition
Allows one of the servo positions to move gradually to a new position
- BYTE	Channel
Range 0-3
- BYTE	Position
Range 0-255
- VOID	Return

	ReadAllValue
Reads a single value stored from the read all command Index dictates which sensor value to read
- BYTE	Index
0=SW, 1-8=IR, 9-10=Line, 11=Light, 12=Mic, 13-15=Accel
- UINT	Return

	LCDBacklight
Allows the LCD backlight brighntess to be adjusted
- BYTE	Intensity
Range 0-100, 0=Off, 1=Min Brightness, 100=Max Brightness
- VOID	Return

	LCDDrawRect
Allows a rectangle to be drawn on the LCD
- BYTE	X1
X Pixel 0-127
- BYTE	Y1
Y Pixel 0-31
- BYTE	X2
X Pixel 0-127
- BYTE	Y2
Y Pixel 0-31
- VOID	Return

	ReadLine
Reads one of the IR line sensors 0-1 0=Left, 1=Right
- BYTE	index
0=Left, 1=Right
- UINT	Return

	ServoDisable
Allows one of the servo outputs 0-3 to be disabled
- BYTE	Channel
Range 0-3
- VOID	Return

	ServoEnable
Allows one of the servo outputs 0-3 to be enabled
- BYTE	Channel
Range 0-3
- VOID	Return

	CardReadByte
Reads a byte from the currently open file. Starts at the beginning of the file and auto increments to the end
- BYTE	Return

	CardErase
Attempts to delete an existing file on the SD card 255=Error, 1=File not found, 0=Delete OK
- STRING	Filename
- BYTE	Return

	CardWriteByte
Appends a byte to the end of the currently open file
- BYTE	Data
- VOID	Return

	EncoderRead
Reads one of the motor encoder counters. Approx 0.328296mm of travel per encoder unit.
- BYTE	index
0=Left, 1=Right
- UINT	Return

	SetMotors
Sets the motor speeds without feedback Range -100 to 100
[[File:]] -	Left
Range -100 to 100
[[File:]] -	Right
Range -100 to 100
- VOID	Return

	Backwards
Drives the robot backwards - waits for the distance to be traversed before returning
- UINT	Distance
Distance in mm
- VOID	Return

	EncoderReset
Resets the motor encoder counters
- VOID	Return

	LCDVerbose
Allows the LCD to automatically report the API commands as they get processed. Default - verbose on
- BYTE	State
0=Off 1=On
- VOID	Return

	SetProp
Allows the COM port property to be set from a parent component.
- STRING	PropName
- ULONG	PropVal
- VOID	Return

	CardInit
Attempts to startup the SD card 255=No Card, 254=Init Fail, 0=Init OK
- BYTE	Return

	GetProp
Allows the property filter for the COM port list to be copied to a parent component.
- STRING	PropName
- STRING	Return

	LCDClear
Clears the LCD
- VOID	Return

Property reference

	Properties
	Circular Buffer Size
Amount of room in the circular buffers before running out of memory. e.g. max command that can be recorded.
	Termination Character
Character that will trigger the AT Injector to automatically switch from recording to repeating.
	Show Console
	Connections
	Simulations