Difference between revisions of "Component: Infrared Array AMG88xx (Light)"
From Flowcode Help
Jump to navigationJump to search (Created page with "{| style="width:50%" |- | width="20%" style="color:gray;" | Author | Matrix TSL |- | width="20%" style="color:gray;" | Version | 1.0 |- | width="20%" style="color:gray...") |
|||
| Line 20: | Line 20: | ||
==Detailed description== | ==Detailed description== | ||
| + | |||
| + | |||
''No detailed description exists yet for this component'' | ''No detailed description exists yet for this component'' | ||
==Examples== | ==Examples== | ||
| + | |||
| + | |||
''<span style="color:red;">No additional examples</span>'' | ''<span style="color:red;">No additional examples</span>'' | ||
Revision as of 14:39, 16 January 2023
| Author | Matrix TSL |
| Version | 1.0 |
| Category | Light |
Contents
Infrared Array AMG88xx component
An 8x8 (64) Pixel infrared sensor array allowing basic none contact temperature detection.
Component Source Code
Please click here for the component source code: FC_Comp_Source_AMG88.fcfx
Detailed description
No detailed description exists yet for this component
Examples
No additional examples
Downloadable macro reference
|
SetMovingAverageMode |
| Set the moving average mode on or off. | |
 - BOOL
|
Mode |
| 0 = Off, 1 = On | |
 - VOID
|
Return |
|
|
ClearInterrupt |
| Clear any triggered interrupts | |
| - VOID
|
Return |
|
|
SetInterruptMode |
| Set the interrupt to either absolute value or difference mode | |
| - BOOL
|
Mode |
| 0 = Difference / 1 = Absolute | |
| - VOID
|
Return |
|
|
SetInterrupt |
| Allows the interrupt pin to be enabled or disabled. | |
| - BOOL
|
Mode |
| 0 = Disabled / 1 = Enabled | |
| - VOID
|
Return |
|
|
SetInterruptLevels |
| Set the interrupt levels. Interrupt when going above High or interrupt when going below Low. | |
 - FLOAT
|
High |
| Range: -1023 to 1023 | |
| - FLOAT
|
Low |
| Range: -1023 to 1023 | |
| - FLOAT
|
Hysteresis |
| Range: -1023 to 1023 ( Recommend 0.95 * High ) | |
| - VOID
|
Return |
|
|
SamplePixels |
| Reads Infrared sensor values | |
| - VOID
|
Return |
|
|
ReadThermistor |
| Reads the onboard thermistor Returns the temperature in degrees Celsius as a floating point value | |
| - FLOAT
|
Return |
|
|
ReadPixel |
| Reads the temperature of a single pixel value from the last SamplePixels call. | |
 - BYTE
|
Index |
| Pixel to read. Range: 0 - 63 | |
| - FLOAT
|
Return |
|
|
Initialise |
| Sets up the I2C interface and initialises the sensor. | |
| - VOID
|
Return |
Property reference
|
Properties |
|
Connections |
|
Address |
|
Channel |
| Channel selection | |
|
SDA |
| Pin used for SDA (data signal) | |
|
|
SCL |
| Pin used for SCL (clock signal) | |
|
|
Baud Select |
| Baud rate option selector | |
|
Baud Rate |
| Baud rate to be used | |
|
Stop Delay |
| On older microcontroller devices there is a potential for the I2C hardware channel to lock up if there is not a 10ms delay between an I2C stop event and the next I2C start event. Most modern microcontrollers will not have a problem so this property can be disabled to speed up the I2C communications. | |
|
|
Simulation |
|
|
Scope Traces |
| Selects if the scope traces are automatically generated or not | |
|
|
Console Data |
| Selects if the console data is automatically generated or not | |
|
|
API |
