Difference between revisions of "Component: Infrared Array AMG88xx (Light)"

Revision as of 11:48, 3 February 2023

Author	Matrix TSL
Version	1.0
Category	Light

Infrared Array AMG88xx component

An 8x8 (64) Pixel infrared sensor array allowing basic none contact temperature detection.

Component Source Code

Please click here to download the component source project: FC_Comp_Source_AMG88.fcfx

Please click here to view the component source code (Beta): FC_Comp_Source_AMG88.fcfx

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Macro reference

SetMovingAverageMode

	SetMovingAverageMode
Set the moving average mode on or off.
- BOOL	Mode
0 = Off, 1 = On
- VOID	Return

ClearInterrupt

	ClearInterrupt
Clear any triggered interrupts
- VOID	Return

SetInterruptMode

	SetInterruptMode
Set the interrupt to either absolute value or difference mode
- BOOL	Mode
0 = Difference / 1 = Absolute
- VOID	Return

SetInterrupt

	SetInterrupt
Allows the interrupt pin to be enabled or disabled.
- BOOL	Mode
0 = Disabled / 1 = Enabled
- VOID	Return

SetInterruptLevels

	SetInterruptLevels
Set the interrupt levels. Interrupt when going above High or interrupt when going below Low.
- FLOAT	High
Range: -1023 to 1023
- FLOAT	Low
Range: -1023 to 1023
- FLOAT	Hysteresis
Range: -1023 to 1023 ( Recommend 0.95 * High )
- VOID	Return

SamplePixels

	SamplePixels
Reads Infrared sensor values
- VOID	Return

ReadThermistor

	ReadThermistor
Reads the onboard thermistor Returns the temperature in degrees Celsius as a floating point value
- FLOAT	Return

ReadPixel

	ReadPixel
Reads the temperature of a single pixel value from the last SamplePixels call.
- BYTE	Index
Pixel to read. Range: 0 - 63
- FLOAT	Return

Initialise

	Initialise
Sets up the I2C interface and initialises the sensor.
- VOID	Return

Property reference

	Properties
	Connections
	Address

	Channel
Channel selection
	SDA
Pin used for SDA (data signal)
	SCL
Pin used for SCL (clock signal)
	Baud Select
Baud rate option selector
	Baud Rate
Baud rate to be used
	Stop Delay
On older microcontroller devices there is a potential for the I2C hardware channel to lock up if there is not a 10ms delay between an I2C stop event and the next I2C start event. Most modern microcontrollers will not have a problem so this property can be disabled to speed up the I2C communications.
	Simulation
	Scope Traces
Selects if the scope traces are automatically generated or not
	Console Data
Selects if the console data is automatically generated or not
	API

@@ Line 56: / Line 56: @@
 ''<span style="color:red;">No additional examples</span>''
@@ Line 61: / Line 63: @@
 ==Macro reference==
+===SetMovingAverageMode===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 79: / Line 82: @@
+===ClearInterrupt===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 92: / Line 96: @@
+===SetInterruptMode===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 110: / Line 115: @@
+===SetInterrupt===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 128: / Line 134: @@
+===SetInterruptLevels===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 156: / Line 163: @@
+===SamplePixels===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 169: / Line 177: @@
+===ReadThermistor===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 182: / Line 191: @@
+===ReadPixel===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-
@@ Line 200: / Line 210: @@
+===Initialise===
 {| class="wikitable" style="width:60%; background-color:#FFFFFF;"
 |-