Component: Robot Arm v2 (AllCode)

Author	Matrix TSL
Version	1.0
Category	AllCode

Robot Arm v2 component

Drives the Matrix Robot Arm v2 hardware via the AllCode API. Allows connections via USB, Bluetooth and WIFI.

Component Source Code

Please click here to download the component source project: FC_Comp_Source_temp/RA2_ComponentSource.fcsx

Please click here to view the component source code (Beta): FC_Comp_Source_temp/RA2_ComponentSource.fcsx

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Macro reference

DisableMotors

	DisableMotors
Disables all motors
- VOID	Return

GetAPI

	GetAPI
Gets the API version number
- BYTE	Return

GetAngles

	GetAngles
Collects the current joint angles of the motors.
- FLOAT	Angles
Float Array To Hold the step position return values
- VOID	Return

GetColourSensor

	GetColourSensor
Samples and returns the RGB values read by the colour sensor
- BYTE	RGB
Byte Array To Hold the RGB sensor values
- VOID	Return

GetPLCInputs

	GetPLCInputs
Reads the inputs on the secondary grove connector used to connect to outputs from a connected PLC or other external switch.
- BYTE	Return

GetPosition

	GetPosition
Collects the current step positions of the motors.
- UINT	Positions
UINT Array To Hold the step position return values
- VOID	Return

GetWifiIP

	GetWifiIP
Collects the IP address of the robot arm WIFI connection.
- STRING	Return

GetXYZ

	GetXYZ
Collects the current XYZ position of the end tool.
- INT	XYZ
INT Array To Hold the X, Y and Z return values
- VOID	Return

GotoPosition

	GotoPosition
Recalls a position from the selected internal none volatile memory location. Performs linear interpolated movement to the selected position.
- BYTE	PositionIndex
Range: 0 to 40
- VOID	Return

HomeAll

	HomeAll
Function to automatically home all motors. Macro blocks until complete.
- VOID	Return

HomeAxis

	HomeAxis
Function to automatically home a specific motor. Macro blocks until complete.
- BYTE	Axis
0=A, 1=B, 2=C
- VOID	Return

Initialise

	Initialise
- BOOL	Return

IsMoving

	IsMoving
Checks to see if the robot arm or gripper is moving. Returns 0 if the arm is not moving and 1 if the arm is still in transit.
- BOOL	Return

ResetToBoot

	ResetToBoot
Resets the board into bootload mode for reprogramming. Comms port will be closed on calling this macro,
- VOID	Return

SetAngle

	SetAngle
Sets the angle of a single motor
- BYTE	Motor
0=A, 1=B, 2=C
- FLOAT	Angle
Range 0.0 to 359.0
- VOID	Return

SetAngles

	SetAngles
Sets the angle of all motors
- FLOAT	AngleA
Range 0.0 to 359.0
- FLOAT	AngleB
Range 0.0 to 359.0
- FLOAT	AngleC
Range 0.0 to 359.0
- VOID	Return

SetBluetoothMode

	SetBluetoothMode
Configures the Bluetooth mode.
- BOOL	Mode
0=Disabled, 1=Enabled
- VOID	Return

SetBluetoothName

	SetBluetoothName
Configures the Bluetooth device name and stores into the none volatie memory onboard the robot arm. Call the SetBluetoothMode macro after this to action the change.
- STRING	Name
Bluetooth Device String, Max 20 Characters
- VOID	Return

SetBluetoothPin

	SetBluetoothPin
Configures the Bluetooth pin and stores into the none volatie memory onboard the robot arm. Call the SetBluetoothMode macro after this to action the change.
- STRING	Pin
Pin String, 4 Numeric Characters e.g. "1234"
- VOID	Return

SetCalibrationLengths

	SetCalibrationLengths
Sets the lengths of parameters A and D used as part of the kinematics calculations to get and set the angles using XYZ coordinates
- FLOAT	LengthA
- FLOAT	LengthD
- VOID	Return

SetCalibrationPosition

	SetCalibrationPosition
Called when the arm gripper is in the calibration position of X0 Y300 Z5 Reconfigures the kinematics calculations based on this. Performed in factory to calibrate the arm, warning calling this function will effect factory calibration.
- VOID	Return

SetCalibrationRadius

	SetCalibrationRadius
Sets the lengths of parameters A and D used as part of the kinematics calculations to get and set the angles using XYZ coordinates
- FLOAT	Radius
- VOID	Return

SetCanId

	SetCanId
Stores the specified CAN ID into an internal none volatile memory location.
- UINT	ID
- VOID	Return

SetCanMode

	SetCanMode
Configures the CAN mode.
- BOOL	Mode
0=Disabled, 1=Enabled
- VOID	Return

SetGripper

	SetGripper
Sets the new position of the gripper
- BYTE	Position
0 = Closed, 255 = Fully Open
- VOID	Return

SetMotor

	SetMotor
Sets the step position of a single motor
- BYTE	Motor
0=A, 1=B, 2=C
- UINT	Position
- VOID	Return

SetMotors

	SetMotors
Sets the step position of all motors
- UINT	PositionA
- UINT	PositionB
- UINT	PositionC
- VOID	Return

SetMovementSpeed

	SetMovementSpeed
Controls the movement speed of the arm and the ramping increment
- UINT	Speed
Range 0-10000 default 8000
- UINT	Increment
Range 0 to 5000, default 50
- VOID	Return

SetRelay

	SetRelay
Allows the vacuum relay to be switched on and off.
- BOOL	State
- VOID	Return

SetWIFIPassword

	SetWIFIPassword
Configures the WIFI Password string and stores into the none volatie memory onboard the robot arm. Call the SetWifiMode macro after this to action the change.
- STRING	Password
Password String, Max 32 Characters
- VOID	Return

SetWIFIPort

	SetWIFIPort
Sets the WIFI port number
- UINT	Port
Default 1245
- VOID	Return

SetWifiMode

	SetWifiMode
Configures the WIFI mode. When enabled the robot arm can either create its own WIFI network or join an existing WIFI network,
- BYTE	Mode
0=Disabled, 1=Host Network, 2=Join Network
- VOID	Return

SetWifiSSID

	SetWifiSSID
Configures the WIFI SSID string and stores into the none volatie memory onboard the robot arm. Call the SetWifiMode macro after this to action the change.
- STRING	SSID
Netword ID String, Max 32 Characters
- VOID	Return

SetXYZ

	SetXYZ
Moves the machine so that the end tool is in the specified XYZ position. Returns 1 if the coordinates are within range of the Arm else returns 0.
- INT	X
- INT	Y
- INT	Z
- BOOL	Return

StoreAngles

	StoreAngles
Stores the specified joint angles into an internal none volatile memory location.
- BYTE	PositionIndex
Range: 0 to 40
- FLOAT	AngleA
Range 0.0 to 359.0
- FLOAT	AngleB
Range 0.0 to 359.0
- FLOAT	AngleC
Range 0.0 to 359.0
- VOID	Return

StoreCurrentPosition

	StoreCurrentPosition
Stores the current position into an internal none volatile memory location.
- BYTE	PositionIndex
Range: 0 to 40
- VOID	Return

StoreMotors

	StoreMotors
Stores the specified step position into an internal none volatile memory location.
- BYTE	PositionIndex
Range: 0 to 40
- UINT	PositionA
- UINT	PositionB
- UINT	PositionC
- VOID	Return

WhileMoving

	WhileMoving
Blocking call that waits up to 10 seconds for the current movement operation to complete. Returns when complete. Return of 1 indicates movement complete, 0 indicates timeout.
- BOOL	Return

Property reference

	Properties
	Simulation Mode
	API Settings
	Comms Method
Selects the method to communicate with the Matrix 3 Axis Robot Arm. USB connection requires the USB drivers to be installed. Bluetooth connection requires the device first be paired using the Windows Bluetooth control panel. WIFI connection requires the connection settings to be configured first on the robot using USB or Bluetooth. CAN connection does not simulate and works on embedded hardware e.g. the MIAC.
	COM Port Settings
	Autodetect
Autodetects the COM port, only works for USB AllCode connection.