Component: Switch Array (Slide) (Switches)

Author	MatrixTSL
Version	11.11
Category	Switches

Switch Array (Slide) component

An array of up to eight slide switches. In embedded mode each switch is connected to a single pin of the specified port.

Version information

Library Version, Component Version, Date, Author, Info
10, 10.0, 26-06-24, MW, Corrected switch and component name bug
12, 11.0, 16-04-25, MW, Corrected bug when sim stopped Switch changed from on to off, but pin remained at VCC
12, 11.0, 16-04-25, MW, Added properties of Ev_PropertiesEX to Ev_Initialise
12, 11.0, 16-04-25, MW, Fixed bug so individual customisation now works
 12, 11.0, 16-04-25, MW, Created a new component icon 

Detailed description

No detailed description exists yet for this component

Examples

Here is an example Flowcode program to read the values of a switch array. Switch Array

Here is a schematic of how to connect a basic switch to a microcontroller pin.

The active high circuit will pass a logical 0 to the input pin when the switch is not pressed and a logical 1 when the switch is pressed.

The active low circuit will pass a logical 1 to the input pin when the switch is not pressed and a logical 0 when the switch is pressed.

There are some differences depending on the type of switch you have, the above states assume a generic push to make type switch, however a push to break type switch would have reversed logic and a toggle switch can work well with either setup.

The resistors are required for correct operation because when a microcontroller's input pin is essentially connected to nothing it will pick up noise in the environment and provide inconsistent readings. This state is referred to as floating i.e. the pin is floating. To test this remove the resistors (if possible) and touch the unconnected pin with your finger the output LED from the example file above will toggle on and off at high speed.

Any values of resistor can be used but it is important to keep the smaller resistor at least 10X smaller then the larger resistor to ensure that the pressed state provides at least 0.91% of the required pressed state voltage. For example a active high switch circuit using 1K and 10K resistors should pull up to about 4.54V when the switch is pressed.

(5V / 11K) * 10K = 4.54545V

Macro reference

ReadAll

	ReadAll
Reads all of the switches at once, returning a byte containing one bit per switch.
- BYTE	Return

ReadState

	ReadState
Read the state of the switch at the given index.
- BYTE	Index
The switch to read the status of.
- BOOL	Return

WaitUntilHigh

	WaitUntilHigh
Pause the program until the switch at the given index is turned on.
- BYTE	Index
Index of the switch to wait for.
- VOID	Return

WaitUntilLow

	WaitUntilLow
Pause the program until the switch at the given index is turned on.
- BYTE	Index
Index of the switch to wait for.
- VOID	Return

Property reference

	Properties
	Switch Settings
	Count
The number of LEDs in the array from 1 to 8.
	Input Mode
Choose a single port for all LEDs - pins are allocated in sequence from pin 0 - 7 ...or choose 'Custom pins' to assign each switch individually.
	Port
	Polarity
Active High = LEDs light when the chosen chip pin is ON Active Low = LEDs light when the chosen chip pin is OFF
	Debounce
Time in milliseconds allowed for the pin to settle following a change of state.
	Operation
Sets whether switches toggle or are press/release. NB) This option can only be set when the original target includes this option.
	Label
	Component Label
Allows you to add your own label to each switch. If Same as Handle is selected then all custom text will be erased.
	Label colour
Colour of the port and pin labels
	Show Connection Label
Enable or disable the pin values underneath each switch
	Show Pin Value
Enable or disable the pin level (GND or VCC) underneath each switch
	Simulation
	Switch layout
	Distance between switches
Set distance betwwn each switch. Default = 55
	Appearance
	Customise individual switches
	Style
	Type
	On Label
	Off Label

Component Source Code

Please click here to download the component source project: FC_Comp_Source_Switch_Array_Slide_2dgi.fcfx

Please click here to view the component source code (Beta): FC_Comp_Source_Switch_Array_Slide_2dgi.fcfx