Component: TCP/IP Dummy (WIZ810MJ) (Comms: Networking)

Author	Matrix Ltd.
Version	2.0
Category	Comms: Networking

TCP/IP Dummy component

TCP/IP component designed to work with the WIZ810MJ module from Wiznet, as used on version 2 EB023 E-block and the MIAC Industrial Addon module.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Macro reference

CreateIPSocket

	CreateIPSocket
Note that sockets on up to 4 channels can be simultaneously opened and these channels are numbered 0 to 3. Note that sockets with different modes can be opened on different channels.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Protocol
Specifies which IP protocol to use
- BYTE	Broadcast
Allows broadcast type packets to be sent and received
- BYTE	Return

CreateMACSocket

	CreateMACSocket
This macro creates a socket for sending and receiving Ethernet data using raw data.
- BYTE	Promiscuous
Receive everything (1) or just data bound for your MAC (0)
- BYTE	Broadcast
Allows broadcast messages to be accepted (1) or rejected (0)
- BYTE	Error
Allowsmessages with errors to be accepted (1) or rejected (0)
- BYTE	Return

CreateTCPSocket

	CreateTCPSocket
This macro creates a socket for sending and receiving TCP data.
- BYTE	Channel
Specifies the communications channel 0-3
- UINT	Src_Port
Port Number
- BYTE	Return

CreateUDPSocket

	CreateUDPSocket
This macro creates a socket for sending and receiving UDP data.
- BYTE	Channel
Specifies the communications channel 0-3
- UINT	Src_Port
Port Number
- BYTE	Return

GetSocketStatus

	GetSocketStatus
This returns the state of the requested channel's socket.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Return

Initialise

	Initialise
Resets and initialises the Internet E-Block. It sets up the gateway address, subnet mask, device IP address and device MAC address as defined in the properties of the Flowcode component. This macro must be called before any other TCP_IP component macros
- BYTE	Return

MIAC_Module_GetData

	MIAC_Module_GetData
- BYTE	Index
- BYTE	Return

MIAC_Module_Message

	MIAC_Module_Message
- UINT	CAN_ID
- UINT	CMD_ID
- BYTE	Return

MIAC_Module_PushData

	MIAC_Module_PushData
- BYTE	Data
- VOID	Return

MIAC_Module_SetData

	MIAC_Module_SetData
- BYTE	Count
- BYTE	D0
- BYTE	D1
- BYTE	D2
- BYTE	D3
- BYTE	D4
- BYTE	D5
- VOID	Return

RxDataAvailable

	RxDataAvailable
This macro is used to check whether or not data has been received by the Internet E-Block. A return value of zero indicated that no data has been received. A positive return value indicates that data is available.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Return

RxDataSize

	RxDataSize
This macro is used to detect the size of data collected by the Rx_data_available macro.
- BYTE	Channel
Specifies the communications channel 0-3
- UINT	Return

RxFlushData

	RxFlushData
Once data reception has been completed, this macro should be called to discard the data packet and allow other data packets to be read.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

RxMatchMyIP

	RxMatchMyIP
This macro returns a non-zero value when the next 4 bytes of data in the specified channel's reception buffer are the same as the Internet E-block's IP address.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Return

RxMatchMyMAC

	RxMatchMyMAC
This macro returns a non-zero value when the next 6 bytes of data in the specified channel's reception buffer are the same as the Internet E-block's MAC address entered in the component's property page.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Return

RxMatch_2_Bytes

	RxMatch_2_Bytes
This macro returns a non-zero value when the next 2 bytes of data in the specified channel's reception buffer are the same as those passed as parameters. There are similar functions that check for 4 bytes and 6 bytes.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Byte1
Specifies the value of the first byte
- BYTE	Byte2
Specifies the value of the second byte
- BYTE	Return

RxMatch_4_Bytes

	RxMatch_4_Bytes
This macro returns a non-zero value when the next 4 bytes of data in the specified channel's reception buffer are the same as those passed as parameters. There are similar functions that check for 2 bytes and 6 bytes.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Byte1
Specifies the value of the first byte
- BYTE	Byte2
Specifies the value of the second byte
- BYTE	Byte3
Specifies the value of the third byte
- BYTE	Byte4
Specifies the value of the fourth byte
- BYTE	Return

RxMatch_6_Bytes

	RxMatch_6_Bytes
This macro returns a non-zero value when the next 6 bytes of data in the specified channel's reception buffer are the same as those passed as parameters. There are similar functions that check for 2 bytes and 4 bytes.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Byte1
Specifies the value of the first byte
- BYTE	Byte2
Specifies the value of the second byte
- BYTE	Byte3
Specifies the value of the third byte
- BYTE	Byte4
Specifies the value of the fourth byte
- BYTE	Byte5
Specifies the value of the fifth byte
- BYTE	Byte6
Specifies the value of the sixth byte
- BYTE	Return

RxReadArray

	RxReadArray
A call to this macro will return a byte of data in the reception buffer of the specified channel. It will also internally increment a pointer to that data so that the next call to 'Rx_readbyte' (or any other read function) will read the next byte
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Data
- UINT	Count
- VOID	Return

RxReadByte

	RxReadByte
A call to this macro will return a byte of data in the reception buffer of the specified channel. It will also internally increment a pointer to that data so that the next call to 'Rx_readbyte' (or any other read function) will read the next byte
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Return

RxReadHeader

	RxReadHeader
Once data in a particular channel has been received, the header will be filled with information about the received data. This macro will return the information in the header. The idx parameter specifies which byte of information in the header to read
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Idx
Specifies the byte index to return
- BYTE	Return

RxReadString

	RxReadString
A call to this macro will return a string of data in the reception buffer of the specified channel. It will also internally increment a pointer to that data so that the next call to 'Rx_readbyte' (or any other read function) will read the next byte
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Length
- STRING	Return

RxSkipBytes

	RxSkipBytes
Often when receiving data packets, it may be necessary to ignore large sections of the data. This can be achieved by reading each byte individually (and ignoring the returned data), but a better way is to use this Rx_skipbytes macro.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Count
Specifies how many bytes to skip
- VOID	Return

SetDestination

	SetDestination
This is used in IP and UDP modes to set the destination of the intended data transfer. The destination IP address needs to be set for both IP and UDP modes.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Dst_IP0
Specifies the first byte of an IP address
- BYTE	Dst_IP1
Specifies the second byte of an IP address
- BYTE	Dst_IP2
Specifies the third byte of an IP address
- BYTE	Dst_IP3
Specifies the fourth byte of an IP address
- UINT	Dst_Port
Destination Port
- BYTE	Return

SetGateway

	SetGateway
This macro sets up the Internet E-Block's Gateway address. In most circumstances, this macro will not be required as the gateway address setting in the component property page will remain constant throughout your application.
- BYTE	IP0
First Byte of IP address
- BYTE	IP1
Second Byte of IP address
- BYTE	IP2
Third Byte of IP address
- BYTE	IP3
Fourth Byte of IP address
- VOID	Return

SetMACAddress

	SetMACAddress
This macro sets up the Internet E-Block's MAC address. In most circumstances, this macro will not be required as the MAC address setting in the component property page will remain constant throughout your application.
- BYTE	MAC0
First Byte of address
- BYTE	MAC1
Second Byte of address
- BYTE	MAC2
Third Byte of address
- BYTE	MAC3
Fourth Byte of address
- BYTE	MAC4
Fourth Byte of address
- BYTE	MAC5
Fifth Byte of address
- VOID	Return

SetMyIP

	SetMyIP
This macro sets up the Internet E-Block's own IP address. In most circumstances, this macro will not be required as the IP address setting in the component property page will remain constant throughout your application.
- BYTE	IP0
First Byte of IP address
- BYTE	IP1
Second Byte of IP address
- BYTE	IP2
Third Byte of IP address
- BYTE	IP3
Fourth Byte of IP address
- VOID	Return

SetSubnetMask

	SetSubnetMask
This macro sets up the Internet E-Block's Subnet Mask. In most circumstances, this macro will not be required as the subnet mask setting in the component property page will remain constant throughout your application.
- BYTE	IP0
First Byte of IP address
- BYTE	IP1
Second Byte of IP address
- BYTE	IP2
Third Byte of IP address
- BYTE	IP3
Fourth Byte of IP address
- VOID	Return

TCPClose

	TCPClose
When an established TCP connection has finished transmission of data, either the local application (i.e. your code) or the remote application (i.e. the application at the other end of the connection) can initiate closure of the socket.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

TCPConnect

	TCPConnect
This macro puts a previously opened TCP channel in "active open" mode. This is the required mode when writing a TCP client application (e.g. using SMTP to send an email).
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Dst_IP0
First Byte of IP address
- BYTE	Dst_IP1
Second Byte of IP address
- BYTE	Dst_IP2
Third Byte of IP address
- BYTE	Dst_IP3
Fourth Byte of IP address
- UINT	Dst_Port
Destination Port
- BYTE	Return

TCPListen

	TCPListen
This macro puts a previously opened TCP channel in "passive open" mode. This is the required mode when writing a TCP server application (e.g. a web server to display HTML web pages).
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

TxEnd

	TxEnd
Once the transmit buffer has been filled with data, call this macro to actually send the data.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

TxSendArray

	TxSendArray
This macro fills the specified channel's transmit buffer with data.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Data
Data byte to append to Tx buffer.
- UINT	Count
- VOID	Return

TxSendByte

	TxSendByte
This macro fills the specified channel's transmit buffer with data. It can fill the buffer with a single byte of data, or with a string of information.
- BYTE	Channel
Specifies the communications channel 0-3
- BYTE	Data
Data byte to append to Tx buffer.
- VOID	Return

TxSendMyIP

	TxSendMyIP
This macro fills the specified channel's transmit buffer with 4 bytes of data representing this Internet E-Block's IP address as specified in the component's property page.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

TxSendMyMAC

	TxSendMyMAC
This macro fills the specified channel's transmit buffer with 6 bytes of data representing this Internet E-Block's MAC address as specified in the component's property page.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

TxSendString

	TxSendString
This macro fills the specified channel's transmit buffer with data. It can fill the buffer with a string of information.
- BYTE	Channel
Specifies the communications channel 0-3
- STRING	Data
Data byte to append to Tx buffer.
- BYTE	Length
- VOID	Return

TxStart

	TxStart
This macro indicates the start of data transmission for the specified buffer. In TCP mode, data transmission can only begin once the socket has become established. In other modes, data transmission can occur as soon as the socket has been opened.
- BYTE	Channel
Specifies the communications channel 0-3
- VOID	Return

Property reference

Properties

Component Source Code

Please click here to download the component source project: FC_Comp_Source_TCPIP_EB023-00-2_Dummy.fcfx

Please click here to view the component source code (Beta): FC_Comp_Source_TCPIP_EB023-00-2_Dummy.fcfx