Component: WIFI (ESP8266) (E-blocks 1): Difference between revisions

Revision as of 10:00, 27 January 2023

Author	Matrix Ltd.
Version	2.1
Category	E-blocks 1

WIFI component

Wireless LAN component designed to work with the ESP8266 module. Provides a very simple interface to allow webpages to be hosted from hardware or simulation.

Component Source Code

Please click here to download the component source project: FC_Comp_Source_WLAN_ESP8266_EB069.fcfx

Please click here to view the component source code (Beta): FC_Comp_Source_WLAN_ESP8266_EB069.fcfx

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Macro reference

	SendString
Sends the given Text with no preappendment. Useful for sending preformatted command strings. Appends a CR to the end of the string if SendCR is greater than 0.
- STRING	Text

- BYTE	SendCR

- VOID	Return

	DisconnectFromSSID
Disconnects from the current SSID. Returns 1 if the command was accepted and returned an "OK"
- BYTE	Return

	ClientConnect
Creates a TCP or UDP connection to a remote server. Returns the state of the connection. 0=Connection failed 1=Connection active
- BYTE	Type
0 = TCP, 1 = UDP
- STRING	IPAddress
e.g. "192.168.1.20"
- UINT	Port
Remote port number to connect to, HTTP comms = Port 80
- BYTE	Return

	ControlTCPServer
Allows a TCP web page server to be switched on and off on the selected port. Returns 1 if the command was completed correctly.
- BYTE	Enable
0 = Stop Server, 1 = Start Server
- UINT	Port
Server port to listen for incoming TCP/IP data requests
- BYTE	Return

	GetFirmwareVersion
Collects the firmware version from the ESP8266 module and returns it as a string.
- STRING	Return

	CheckForPageRequests
To be called periodically. Returns non-zero if a request has been processed
- BYTE	Return

	ClientSendRequest
Sends out a string with the required AT+CIPSEND=Length$(Request) initialiser.
- STRING	Request
e.g. "GET / HTTP/1.0\r\n\r\n"
- VOID	Return

	ReadSSIDFromScan
Collects one of the SSID name strings from the last SSID Scan. The ScanForSSID macro must be called first.
- BYTE	Index
SSID Index
- STRING	Return

	CreateAccessPoint
Sets up the wireless LAN module into AP mode to host a wireless network. Other WIFI enabled devices can then connect to the module. Returns 1 for success.
- STRING	SSID
Name of the wireless network to create
- STRING	Password
Password used to gain access to the network
- BYTE	Channel
802.11 Channel Range 1-14
- BYTE	Encryption
0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Return

	SetOutValue
Set the value of an outbound substitution string
- BYTE	index
Range 0-4
- STRING	value

- VOID	Return

	EndServerConnection
Disconnects from the current active TCP/IP pipe.
- BYTE	Return

	Send_Embedded_HTML_Page4

- VOID	Return

	ReadSignalStrengthFromScan
Collects the signal strength from the last SSID Scan. The ScanForSSID macro must be called first. Value returned is in negative dB, smaller value = better signal
- BYTE	Index
SSID Index
- INT	Return

	Send_Embedded_HTML_Page3

- VOID	Return

	Send_Embedded_HTML_Page2

- VOID	Return

	Send_Embedded_HTML_Page1

- VOID	Return

	ReadEncryptionModeFromScan
Collects one of the encryption modes from the last SSID Scan. The ScanForSSID macro must be called first. 0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Index
SSID Index
- BYTE	Return

	GetByteWithTimeout
Attempts to receive a byte from the circular buffer. If nothing is available then waits up to 200 ms for data to become available.
- BYTE	Return

	GetInValue
Returns the string value of a Request parameter
- BYTE	index
Index of the request paramter, starting at zero Range 0-2
- STRING	Return

	ConnectToSSID
Attempts to connect to the given SSID and Key values. Returns 1 if the SSID has been connected.
- STRING	SSID

- STRING	Key

- BYTE	Timeout
Number of seconds to wait for the connection, default 20
- BYTE	Return

	ClientSendArray
Sends out an array of data bytes with the required AT+CIPSEND=Length$(Request) initialiser.
- BYTE	Data

- UINT	NumBytes

- VOID	Return

	GetRxArray
Attempts to receive a number of bytes from the remote connection If nothing is available then waits up to 200 ms for data to become available. Returns the number of bytes received,.
- BYTE	Data
Byte array to store the incoming data
- UINT	MaxBytes
Maximum number of bytes to try and receive
- UINT	Return

	ScanForSSID
Checks for wireless networks in the local area which are broadcasting their SSID. Must not be connected to a network to allow this to function. Returns the number of wireless networks found, max 8.
- BYTE	Return

	Initialise
Initialise the device with the property data. Returns 1 if "ready" message successfully received Returns 0 if no reply from module
- BYTE	Return

	CheckTCPServerIP
Collects the local IP address of the active TCP server.
- STRING	Return

Property reference

	Properties
	WIFI Properties
	Receive Buffer Size
Buffer used to store incoming data ready for processing. Default 128 Bytes.
	Scan Buffer Size
Buffer used to hold SSID names when performing a SSID network scan. Default 100 Bytes.
	Reset Mode
The initialise automatically resets the WIFI module before establishing communications. Software reset uses an AT command to preform the reset Hardware reset uses an extra I/O pin to toggle the signal to the reset pin on the module.
	Command Termination
Older versions of the firmware require \r to terminate a AT command string. Newer versions of the firmware have changed to use \r\n termination.
	Connections
	Channel
UART Channel selector Software channels are bit banged using generic I/O pins but are not as reliable as hardware channels. Hardware channels use the selected peripheral on-board the target microcontroller.
	Baud Options
Baud rate option selector
	Baud Rate

	TX
Pin to be used for Transmit data
	RX
Pin to be used for Receive data
	Reset
WLAN module reset pin connection
	Use Flow Control
Flow Control (Handshake) enable or disable. On: Two I/O pins are used to control the flow of data in and out of the device. Off: Flow control is disabled.
	HTML Source
	Max Web Pages
Maximum number of individual webpages we can serve up with the component.
	Web Page Timeout
Number of cycles to try and send / receive a webpage before timing out.
	Line Delay
Fixed delay in microseconds sent in between sending a HTML line when running as a web page server.
	Name Page 1
HTML name of webpage 1
	HTML Page 1
HTML content for webpage 1
	Name Page 2
HTML name of webpage 2
	HTML Page 2
HTML content for webpage 2
	Name Page 3
HTML name of webpage 3
	HTML Page 3
HTML content for webpage 3
	Name Page 4
HTML name of webpage 4
	HTML Page 4
HTML content for webpage 4
	Substitutions
	Outgoing
	Count
Maximum number of outbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Incoming
	Count
Maximum number of inbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Simulation
	Label
Text label used to help identify the component on the panel.
	Simulation Method
Decides how to handle the simulation of the component. TCP Base - Allows simulation of the network communications using the TCP Base component and DLL. COM/Injector - Allows the simulation to connect to real hardware or injectors.
	Data Recorder Traces
Selects if the scope traces are automatically added to the data recorder window or not. Simulation - draws an approximation of the UART data onto the scope trace. ICT - sets up the scope trace for incoming data and adds UART packet decoding at the correct BAUD.
	Console Data
Selects if the console data is automatically generated or not
	Console Columns
Number of characters that can be displayed on a single line of the console.
	Communications
	Data Source
Simulation data source used to allow the component to connect to various remote devices Nothing - Simulation data is ignored COM port - Routes the communication data to and from a physical or virtual COM port Injector - Routes the communication data via a data injector component on the Panel.

==Macro reference==

	SendString
Sends the given Text with no preappendment. Useful for sending preformatted command strings. Appends a CR to the end of the string if SendCR is greater than 0.
- STRING	Text

- BYTE	SendCR

- VOID	Return

	DisconnectFromSSID
Disconnects from the current SSID. Returns 1 if the command was accepted and returned an "OK"
- BYTE	Return

	ClientConnect
Creates a TCP or UDP connection to a remote server. Returns the state of the connection. 0=Connection failed 1=Connection active
- BYTE	Type
0 = TCP, 1 = UDP
- STRING	IPAddress
e.g. "192.168.1.20"
- UINT	Port
Remote port number to connect to, HTTP comms = Port 80
- BYTE	Return

	ControlTCPServer
Allows a TCP web page server to be switched on and off on the selected port. Returns 1 if the command was completed correctly.
- BYTE	Enable
0 = Stop Server, 1 = Start Server
- UINT	Port
Server port to listen for incoming TCP/IP data requests
- BYTE	Return

	GetFirmwareVersion
Collects the firmware version from the ESP8266 module and returns it as a string.
- STRING	Return

	CheckForPageRequests
To be called periodically. Returns non-zero if a request has been processed
- BYTE	Return

	ClientSendRequest
Sends out a string with the required AT+CIPSEND=Length$(Request) initialiser.
- STRING	Request
e.g. "GET / HTTP/1.0\r\n\r\n"
- VOID	Return

	ReadSSIDFromScan
Collects one of the SSID name strings from the last SSID Scan. The ScanForSSID macro must be called first.
- BYTE	Index
SSID Index
- STRING	Return

	CreateAccessPoint
Sets up the wireless LAN module into AP mode to host a wireless network. Other WIFI enabled devices can then connect to the module. Returns 1 for success.
- STRING	SSID
Name of the wireless network to create
- STRING	Password
Password used to gain access to the network
- BYTE	Channel
802.11 Channel Range 1-14
- BYTE	Encryption
0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Return

	SetOutValue
Set the value of an outbound substitution string
- BYTE	index
Range 0-4
- STRING	value

- VOID	Return

	EndServerConnection
Disconnects from the current active TCP/IP pipe.
- BYTE	Return

	Send_Embedded_HTML_Page4

- VOID	Return

	ReadSignalStrengthFromScan
Collects the signal strength from the last SSID Scan. The ScanForSSID macro must be called first. Value returned is in negative dB, smaller value = better signal
- BYTE	Index
SSID Index
- INT	Return

	Send_Embedded_HTML_Page3

- VOID	Return

	Send_Embedded_HTML_Page2

- VOID	Return

	Send_Embedded_HTML_Page1

- VOID	Return

	ReadEncryptionModeFromScan
Collects one of the encryption modes from the last SSID Scan. The ScanForSSID macro must be called first. 0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Index
SSID Index
- BYTE	Return

	GetByteWithTimeout
Attempts to receive a byte from the circular buffer. If nothing is available then waits up to 200 ms for data to become available.
- BYTE	Return

	GetInValue
Returns the string value of a Request parameter
- BYTE	index
Index of the request paramter, starting at zero Range 0-2
- STRING	Return

	ConnectToSSID
Attempts to connect to the given SSID and Key values. Returns 1 if the SSID has been connected.
- STRING	SSID

- STRING	Key

- BYTE	Timeout
Number of seconds to wait for the connection, default 20
- BYTE	Return

	ClientSendArray
Sends out an array of data bytes with the required AT+CIPSEND=Length$(Request) initialiser.
- BYTE	Data

- UINT	NumBytes

- VOID	Return

	GetRxArray
Attempts to receive a number of bytes from the remote connection If nothing is available then waits up to 200 ms for data to become available. Returns the number of bytes received,.
- BYTE	Data
Byte array to store the incoming data
- UINT	MaxBytes
Maximum number of bytes to try and receive
- UINT	Return

	ScanForSSID
Checks for wireless networks in the local area which are broadcasting their SSID. Must not be connected to a network to allow this to function. Returns the number of wireless networks found, max 8.
- BYTE	Return

	Initialise
Initialise the device with the property data. Returns 1 if "ready" message successfully received Returns 0 if no reply from module
- BYTE	Return

	CheckTCPServerIP
Collects the local IP address of the active TCP server.
- STRING	Return

Property reference

	Properties
	WIFI Properties
	Receive Buffer Size
Buffer used to store incoming data ready for processing. Default 128 Bytes.
	Scan Buffer Size
Buffer used to hold SSID names when performing a SSID network scan. Default 100 Bytes.
	Reset Mode
The initialise automatically resets the WIFI module before establishing communications. Software reset uses an AT command to preform the reset Hardware reset uses an extra I/O pin to toggle the signal to the reset pin on the module.
	Command Termination
Older versions of the firmware require \r to terminate a AT command string. Newer versions of the firmware have changed to use \r\n termination.
	Connections
	Channel
UART Channel selector Software channels are bit banged using generic I/O pins but are not as reliable as hardware channels. Hardware channels use the selected peripheral on-board the target microcontroller.
	Baud Options
Baud rate option selector
	Baud Rate

	TX
Pin to be used for Transmit data
	RX
Pin to be used for Receive data
	Reset
WLAN module reset pin connection
	Use Flow Control
Flow Control (Handshake) enable or disable. On: Two I/O pins are used to control the flow of data in and out of the device. Off: Flow control is disabled.
	HTML Source
	Max Web Pages
Maximum number of individual webpages we can serve up with the component.
	Web Page Timeout
Number of cycles to try and send / receive a webpage before timing out.
	Line Delay
Fixed delay in microseconds sent in between sending a HTML line when running as a web page server.
	Name Page 1
HTML name of webpage 1
	HTML Page 1
HTML content for webpage 1
	Name Page 2
HTML name of webpage 2
	HTML Page 2
HTML content for webpage 2
	Name Page 3
HTML name of webpage 3
	HTML Page 3
HTML content for webpage 3
	Name Page 4
HTML name of webpage 4
	HTML Page 4
HTML content for webpage 4
	Substitutions
	Outgoing
	Count
Maximum number of outbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Incoming
	Count
Maximum number of inbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Simulation
	Label
Text label used to help identify the component on the panel.
	Simulation Method
Decides how to handle the simulation of the component. TCP Base - Allows simulation of the network communications using the TCP Base component and DLL. COM/Injector - Allows the simulation to connect to real hardware or injectors.
	Data Recorder Traces
Selects if the scope traces are automatically added to the data recorder window or not. Simulation - draws an approximation of the UART data onto the scope trace. ICT - sets up the scope trace for incoming data and adds UART packet decoding at the correct BAUD.
	Console Data
Selects if the console data is automatically generated or not
	Console Columns
Number of characters that can be displayed on a single line of the console.
	Communications
	Data Source
Simulation data source used to allow the component to connect to various remote devices Nothing - Simulation data is ignored COM port - Routes the communication data to and from a physical or virtual COM port Injector - Routes the communication data via a data injector component on the Panel.

==Macro reference==

	SendString
Sends the given Text with no preappendment. Useful for sending preformatted command strings. Appends a CR to the end of the string if SendCR is greater than 0.
- STRING	Text

- BYTE	SendCR

- VOID	Return

	DisconnectFromSSID
Disconnects from the current SSID. Returns 1 if the command was accepted and returned an "OK"
- BYTE	Return

	ClientConnect
Creates a TCP or UDP connection to a remote server. Returns the state of the connection. 0=Connection failed 1=Connection active
- BYTE	Type
0 = TCP, 1 = UDP
- STRING	IPAddress
e.g. "192.168.1.20"
- UINT	Port
Remote port number to connect to, HTTP comms = Port 80
- BYTE	Return

	ControlTCPServer
Allows a TCP web page server to be switched on and off on the selected port. Returns 1 if the command was completed correctly.
- BYTE	Enable
0 = Stop Server, 1 = Start Server
- UINT	Port
Server port to listen for incoming TCP/IP data requests
- BYTE	Return

	GetFirmwareVersion
Collects the firmware version from the ESP8266 module and returns it as a string.
- STRING	Return

	CheckForPageRequests
To be called periodically. Returns non-zero if a request has been processed
- BYTE	Return

	ClientSendRequest
Sends out a string with the required AT+CIPSEND=Length$(Request) initialiser.
- STRING	Request
e.g. "GET / HTTP/1.0\r\n\r\n"
- VOID	Return

	ReadSSIDFromScan
Collects one of the SSID name strings from the last SSID Scan. The ScanForSSID macro must be called first.
- BYTE	Index
SSID Index
- STRING	Return

	CreateAccessPoint
Sets up the wireless LAN module into AP mode to host a wireless network. Other WIFI enabled devices can then connect to the module. Returns 1 for success.
- STRING	SSID
Name of the wireless network to create
- STRING	Password
Password used to gain access to the network
- BYTE	Channel
802.11 Channel Range 1-14
- BYTE	Encryption
0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Return

	SetOutValue
Set the value of an outbound substitution string
- BYTE	index
Range 0-4
- STRING	value

- VOID	Return

	EndServerConnection
Disconnects from the current active TCP/IP pipe.
- BYTE	Return

	Send_Embedded_HTML_Page4

- VOID	Return

	ReadSignalStrengthFromScan
Collects the signal strength from the last SSID Scan. The ScanForSSID macro must be called first. Value returned is in negative dB, smaller value = better signal
- BYTE	Index
SSID Index
- INT	Return

	Send_Embedded_HTML_Page3

- VOID	Return

	Send_Embedded_HTML_Page2

- VOID	Return

	Send_Embedded_HTML_Page1

- VOID	Return

	ReadEncryptionModeFromScan
Collects one of the encryption modes from the last SSID Scan. The ScanForSSID macro must be called first. 0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Index
SSID Index
- BYTE	Return

	GetByteWithTimeout
Attempts to receive a byte from the circular buffer. If nothing is available then waits up to 200 ms for data to become available.
- BYTE	Return

	GetInValue
Returns the string value of a Request parameter
- BYTE	index
Index of the request paramter, starting at zero Range 0-2
- STRING	Return

	ConnectToSSID
Attempts to connect to the given SSID and Key values. Returns 1 if the SSID has been connected.
- STRING	SSID

- STRING	Key

- BYTE	Timeout
Number of seconds to wait for the connection, default 20
- BYTE	Return

	ClientSendArray
Sends out an array of data bytes with the required AT+CIPSEND=Length$(Request) initialiser.
- BYTE	Data

- UINT	NumBytes

- VOID	Return

	GetRxArray
Attempts to receive a number of bytes from the remote connection If nothing is available then waits up to 200 ms for data to become available. Returns the number of bytes received,.
- BYTE	Data
Byte array to store the incoming data
- UINT	MaxBytes
Maximum number of bytes to try and receive
- UINT	Return

	ScanForSSID
Checks for wireless networks in the local area which are broadcasting their SSID. Must not be connected to a network to allow this to function. Returns the number of wireless networks found, max 8.
- BYTE	Return

	Initialise
Initialise the device with the property data. Returns 1 if "ready" message successfully received Returns 0 if no reply from module
- BYTE	Return

	CheckTCPServerIP
Collects the local IP address of the active TCP server.
- STRING	Return

Property reference

	Properties
	WIFI Properties
	Receive Buffer Size
Buffer used to store incoming data ready for processing. Default 128 Bytes.
	Scan Buffer Size
Buffer used to hold SSID names when performing a SSID network scan. Default 100 Bytes.
	Reset Mode
The initialise automatically resets the WIFI module before establishing communications. Software reset uses an AT command to preform the reset Hardware reset uses an extra I/O pin to toggle the signal to the reset pin on the module.
	Command Termination
Older versions of the firmware require \r to terminate a AT command string. Newer versions of the firmware have changed to use \r\n termination.
	Connections
	Channel
UART Channel selector Software channels are bit banged using generic I/O pins but are not as reliable as hardware channels. Hardware channels use the selected peripheral on-board the target microcontroller.
	Baud Options
Baud rate option selector
	Baud Rate

	TX
Pin to be used for Transmit data
	RX
Pin to be used for Receive data
	Reset
WLAN module reset pin connection
	Use Flow Control
Flow Control (Handshake) enable or disable. On: Two I/O pins are used to control the flow of data in and out of the device. Off: Flow control is disabled.
	HTML Source
	Max Web Pages
Maximum number of individual webpages we can serve up with the component.
	Web Page Timeout
Number of cycles to try and send / receive a webpage before timing out.
	Line Delay
Fixed delay in microseconds sent in between sending a HTML line when running as a web page server.
	Name Page 1
HTML name of webpage 1
	HTML Page 1
HTML content for webpage 1
	Name Page 2
HTML name of webpage 2
	HTML Page 2
HTML content for webpage 2
	Name Page 3
HTML name of webpage 3
	HTML Page 3
HTML content for webpage 3
	Name Page 4
HTML name of webpage 4
	HTML Page 4
HTML content for webpage 4
	Substitutions
	Outgoing
	Count
Maximum number of outbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Incoming
	Count
Maximum number of inbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Simulation
	Label
Text label used to help identify the component on the panel.
	Simulation Method
Decides how to handle the simulation of the component. TCP Base - Allows simulation of the network communications using the TCP Base component and DLL. COM/Injector - Allows the simulation to connect to real hardware or injectors.
	Data Recorder Traces
Selects if the scope traces are automatically added to the data recorder window or not. Simulation - draws an approximation of the UART data onto the scope trace. ICT - sets up the scope trace for incoming data and adds UART packet decoding at the correct BAUD.
	Console Data
Selects if the console data is automatically generated or not
	Console Columns
Number of characters that can be displayed on a single line of the console.
	Communications
	Data Source
Simulation data source used to allow the component to connect to various remote devices Nothing - Simulation data is ignored COM port - Routes the communication data to and from a physical or virtual COM port Injector - Routes the communication data via a data injector component on the Panel.

==Macro reference==

	SendString
Sends the given Text with no preappendment. Useful for sending preformatted command strings. Appends a CR to the end of the string if SendCR is greater than 0.
- STRING	Text

- BYTE	SendCR

- VOID	Return

	DisconnectFromSSID
Disconnects from the current SSID. Returns 1 if the command was accepted and returned an "OK"
- BYTE	Return

	ClientConnect
Creates a TCP or UDP connection to a remote server. Returns the state of the connection. 0=Connection failed 1=Connection active
- BYTE	Type
0 = TCP, 1 = UDP
- STRING	IPAddress
e.g. "192.168.1.20"
- UINT	Port
Remote port number to connect to, HTTP comms = Port 80
- BYTE	Return

	ControlTCPServer
Allows a TCP web page server to be switched on and off on the selected port. Returns 1 if the command was completed correctly.
- BYTE	Enable
0 = Stop Server, 1 = Start Server
- UINT	Port
Server port to listen for incoming TCP/IP data requests
- BYTE	Return

	GetFirmwareVersion
Collects the firmware version from the ESP8266 module and returns it as a string.
- STRING	Return

	CheckForPageRequests
To be called periodically. Returns non-zero if a request has been processed
- BYTE	Return

	ClientSendRequest
Sends out a string with the required AT+CIPSEND=Length$(Request) initialiser.
- STRING	Request
e.g. "GET / HTTP/1.0\r\n\r\n"
- VOID	Return

	ReadSSIDFromScan
Collects one of the SSID name strings from the last SSID Scan. The ScanForSSID macro must be called first.
- BYTE	Index
SSID Index
- STRING	Return

	CreateAccessPoint
Sets up the wireless LAN module into AP mode to host a wireless network. Other WIFI enabled devices can then connect to the module. Returns 1 for success.
- STRING	SSID
Name of the wireless network to create
- STRING	Password
Password used to gain access to the network
- BYTE	Channel
802.11 Channel Range 1-14
- BYTE	Encryption
0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Return

	SetOutValue
Set the value of an outbound substitution string
- BYTE	index
Range 0-4
- STRING	value

- VOID	Return

	EndServerConnection
Disconnects from the current active TCP/IP pipe.
- BYTE	Return

	Send_Embedded_HTML_Page4

- VOID	Return

	ReadSignalStrengthFromScan
Collects the signal strength from the last SSID Scan. The ScanForSSID macro must be called first. Value returned is in negative dB, smaller value = better signal
- BYTE	Index
SSID Index
- INT	Return

	Send_Embedded_HTML_Page3

- VOID	Return

	Send_Embedded_HTML_Page2

- VOID	Return

	Send_Embedded_HTML_Page1

- VOID	Return

	ReadEncryptionModeFromScan
Collects one of the encryption modes from the last SSID Scan. The ScanForSSID macro must be called first. 0=Open, 1=WEP, 2=WPA_PSK, 3=WPA2_PSK, 4=WPA_WPA2_PSK
- BYTE	Index
SSID Index
- BYTE	Return

	GetByteWithTimeout
Attempts to receive a byte from the circular buffer. If nothing is available then waits up to 200 ms for data to become available.
- BYTE	Return

	GetInValue
Returns the string value of a Request parameter
- BYTE	index
Index of the request paramter, starting at zero Range 0-2
- STRING	Return

	ConnectToSSID
Attempts to connect to the given SSID and Key values. Returns 1 if the SSID has been connected.
- STRING	SSID

- STRING	Key

- BYTE	Timeout
Number of seconds to wait for the connection, default 20
- BYTE	Return

	ClientSendArray
Sends out an array of data bytes with the required AT+CIPSEND=Length$(Request) initialiser.
- BYTE	Data

- UINT	NumBytes

- VOID	Return

	GetRxArray
Attempts to receive a number of bytes from the remote connection If nothing is available then waits up to 200 ms for data to become available. Returns the number of bytes received,.
- BYTE	Data
Byte array to store the incoming data
- UINT	MaxBytes
Maximum number of bytes to try and receive
- UINT	Return

	ScanForSSID
Checks for wireless networks in the local area which are broadcasting their SSID. Must not be connected to a network to allow this to function. Returns the number of wireless networks found, max 8.
- BYTE	Return

	Initialise
Initialise the device with the property data. Returns 1 if "ready" message successfully received Returns 0 if no reply from module
- BYTE	Return

	CheckTCPServerIP
Collects the local IP address of the active TCP server.
- STRING	Return

Property reference

	Properties
	WIFI Properties
	Receive Buffer Size
Buffer used to store incoming data ready for processing. Default 128 Bytes.
	Scan Buffer Size
Buffer used to hold SSID names when performing a SSID network scan. Default 100 Bytes.
	Reset Mode
The initialise automatically resets the WIFI module before establishing communications. Software reset uses an AT command to preform the reset Hardware reset uses an extra I/O pin to toggle the signal to the reset pin on the module.
	Command Termination
Older versions of the firmware require \r to terminate a AT command string. Newer versions of the firmware have changed to use \r\n termination.
	Connections
	Channel
UART Channel selector Software channels are bit banged using generic I/O pins but are not as reliable as hardware channels. Hardware channels use the selected peripheral on-board the target microcontroller.
	Baud Options
Baud rate option selector
	Baud Rate

	TX
Pin to be used for Transmit data
	RX
Pin to be used for Receive data
	Reset
WLAN module reset pin connection
	Use Flow Control
Flow Control (Handshake) enable or disable. On: Two I/O pins are used to control the flow of data in and out of the device. Off: Flow control is disabled.
	HTML Source
	Max Web Pages
Maximum number of individual webpages we can serve up with the component.
	Web Page Timeout
Number of cycles to try and send / receive a webpage before timing out.
	Line Delay
Fixed delay in microseconds sent in between sending a HTML line when running as a web page server.
	Name Page 1
HTML name of webpage 1
	HTML Page 1
HTML content for webpage 1
	Name Page 2
HTML name of webpage 2
	HTML Page 2
HTML content for webpage 2
	Name Page 3
HTML name of webpage 3
	HTML Page 3
HTML content for webpage 3
	Name Page 4
HTML name of webpage 4
	HTML Page 4
HTML content for webpage 4
	Substitutions
	Outgoing
	Count
Maximum number of outbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Incoming
	Count
Maximum number of inbound string substitutions
	Length 0
Number of bytes to reserve for data string.
	Simulation
	Label
Text label used to help identify the component on the panel.
	Simulation Method
Decides how to handle the simulation of the component. TCP Base - Allows simulation of the network communications using the TCP Base component and DLL. COM/Injector - Allows the simulation to connect to real hardware or injectors.
	Data Recorder Traces
Selects if the scope traces are automatically added to the data recorder window or not. Simulation - draws an approximation of the UART data onto the scope trace. ICT - sets up the scope trace for incoming data and adds UART packet decoding at the correct BAUD.
	Console Data
Selects if the console data is automatically generated or not
	Console Columns
Number of characters that can be displayed on a single line of the console.
	Communications
	Data Source
Simulation data source used to allow the component to connect to various remote devices Nothing - Simulation data is ignored COM port - Routes the communication data to and from a physical or virtual COM port Injector - Routes the communication data via a data injector component on the Panel.

Wiki bot (talk | contribs)

Revision as of 10:00, 27 January 2023

WIFI component

Component Source Code

Detailed description

Examples

Macro reference

Property reference

Property reference

Property reference

Property reference