Component: Electrical Machines (AllCode)

Author	Matrix TSL
Version	2.0
Category	AllCode

Electrical Machines component

A set of functions to communicate with the Matrix EM hardware. Allows the functions to be easily standardised across all SCADA programs.

Component Source Code

Please click here to download the component source project: FC_Comp_Source_EM_Functions.fcsx

Please click here to view the component source code (Beta): FC_Comp_Source_EM_Functions.fcsx

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Macro reference

	GetLogDataReady
Checks to see if the logging is complete and ready to read.
- BOOL	Return

	GetRPM
Reads the speed in RPM
- UINT	Return

	GetWeight
Reads the voltage of a single channel
- BYTE	Scale
Range: 0-1 - 0=Weight, 1=Torque
- FLOAT	Return

	SetControlKP
- FLOAT	Value
- VOID	Return

	SetControlSetpoint
- FLOAT	Value
- VOID	Return

	GetAPIVersion
Reads the API firmware version
- BYTE	Return

	GetLogData
Gets a 64-byte packet of log data. 250 packets make up a single log. Returns 0 if comms failed and 1 if comms OK
- BYTE	Buffer
Buffer to store the incoming log data
- BOOL	Return

	GetDataArray
Collects a data array from the EM box full of control data. Each set of data includes: Setpoint, Feedback, Poutput, Ioutput, Doutput Returns the number of complete data samples collected.
- FLOAT	data
- BYTE	Return

	GetSafetySwitch
Reads the safety switch
- UINT	Return

	SetControlKI
- FLOAT	Value
- VOID	Return

	ZeroLoadCell
- VOID	Return

	SetControlMaxDrivePercentage
- FLOAT	Value
Range 0.0-1.0
- VOID	Return

	SetMotorType
- BYTE	MotorType
0=DC, 1=1 Phase, 2=3 Phase
- VOID	Return

	SetLoadCellCalibration
- FLOAT	Value
- VOID	Return

	GetVoltage
Reads the voltage of a single channel
- BYTE	Channel
Range: 0-5 - 0=DC1, 1=DC2, 2=U, 3=V, 4=W, 5=VEXT
- FLOAT	Return

	GetControlFeedback
- FLOAT	Return

	SetControlKD
- FLOAT	Value
- VOID	Return

	SetCapacitorBank
- BYTE	Cap
- VOID	Return

	GetCommsOK
Checks if comms are ok and stable
- BOOL	Return

	GetLogStartAngle
Collects the U Phase angle at the start of logging. Used to calculate and re-create the 3Phase voltage data.
- BYTE	Return

	SetVoltage
Sets the DC Voltage from 0 to 24V
- FLOAT	Voltage
- BYTE	Index
- VOID	Return

	Get3PhaseMode
Checks to see if the brushless mode is enabled
- BOOL	Return

	GetAbsPosition
Reads the absolute position of the encoder
- ULONG	Return

	SetFan
|Sets the speed of the FAN from 0 (MIN) to 3000 (MAX)
- UINT	Speed
- VOID	Return

	SetMotorDirection
- BOOL	MotorDirection
0=FW, 1=BW
- VOID	Return

	GetMotorDirection
Reads the motor direction
- UINT	Return

	SetThreePhaseDriveMode
- BOOL	Mode
0=Simple, 1=Accurate
- VOID	Return

	GetCurrent
Reads the current of a single channel
- BYTE	Channel
Range: 0-6 - 0=DC1, 1=DC2, 2=U, 3=V, 4=W, 5=Dyno, 6=I, 7=TotalDriver
- FLOAT	Return

	SetFrequency
- UINT	Frequency
Frequency of sine wave in Hz
- VOID	Return

	SetDynoLoad
- FLOAT	Load
- VOID	Return

	GetErrorStatus
Gets the current error status. Error status will automatically resolve itself once the causing condition has been removed. 0 = No Error 1 = Error - likely over current or brownout
- BYTE	Return

	GetControlOutputs
- FLOAT	Data
- VOID	Return

	SetActive
- BOOL	Active
0=Off, 1=On
- VOID	Return

	SetDriveMode
- BYTE	Mode
0=PWM, 1=On/Off/Float
- VOID	Return

	SetTCPProps
Sets the TCP IP address and Port
- BYTE	IP0
- BYTE	IP1
- BYTE	IP2
- BYTE	IP3
- UINT	Port
- VOID	Return

	SetAbsPosition
Resets the absolute motor position to 0
- VOID	Return

	Initialise
Returns 1 if the connection is ok and communications have been established
- BYTE	MotorType
0=DC, 1=1Phase, 2=3Phase, 3=AngleControl
- BOOL	Return

Property reference

	Properties
	Communications
	Comms Mode
	Stop On Error
Automatically allows the runtime to stop if there is a communications error.
	USB Communications
	Autodetect Port
	Runtime Statistics
	Console Data
Allow console data to be generated showing the high level EM communications and returns