Component: Thermistor (Environmental)

Author	Matrix TSL
Version	1.1
Category	Environmental

Thermistor component

A generic thermistor component that can be used to simulate and create code for any thermistor with a known temperature/resistance curve. Thermistor is connected in a simple potential divider circuit - thermistor between ADC input and 0V, and a fixed resistor between ADC and the positive supply. Default calibration is for the EBM003 module.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	GetIntegerTemperature
Reads the ADC input and returns the calculated Temperature as Integer degrees C
[[File:]] -	Return

	SetChannel
Set the ADC Channel
[[File:]] -	ChannelID
- VOID	Return

	SetMinMax
Set the minimum and maximum temperature values that can be shown and set on the thermometer readout.
[[File:]] -	Min
Minimum Value
[[File:]] -	Max
Maximum Value
- VOID	Return

	GetRealTemperature
Reads the ADC input and Returns the calculated Temperature as Float value in degrees C
[[File:]] -	Return

	SetTemperature
Sends the given temperature to the display, and calculates the internal values used by the simulated read macros.
[[File:]] -	Temperature
Zero to one value - representing min-max of the sensor.
- VOID	Return

	CalculateTemperature
Converts the input ADC value and returns the Temperature in tenths of degree C
- UINT	ADCValue
ADC Reading to be converted
[[File:]] -	Return

	GetADCValue
Returns the Raw ADC value from the Analogue Channel
- UINT	Return

	Initialise
Initialise to default of 11 bit resolution
- BYTE	Return

	Initialise
Configures each matching sensor on the bus with the specified conversion bits.
- VOID	Return

	WriteRegister
A simple example showing a generic way to write a register using I2C.
- BYTE	Address
- BYTE	Data
- VOID	Return

	Initialise
[[File:]] -	Return

	Initialise
Sets up up the communication bus and initialises the accelerometer module. Returns 0 for success and > 0 for fail.
- BYTE	Return

	IOSetOutputPin
Sets the selected digital pin to an output and assigns the output state.
- BYTE	Pin
Range: 0-29
[[File:]] -	State
Range: 0-1
- VOID	Return

	UARTReceive
Receives a data byte from the UART. Recommend calling the UARTCheckRx function first to ensure data is available.
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Return

	ADCSampleAverage10
Reads the voltage present on an Analog pin as an 10-bit value range 0-1023. Performs the selected number of samples with the selected time in microseconds in between samples
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 100
- BYTE	SampleDelay
Delay in us between each sample
- UINT	Return

	OneWireScanBus
Scans the one wire bus to detect all connected devices. Returns the number of one wire devices found.
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	SPIInitialise
Initialsie the SPI module ready for communications
- BYTE	Channel
Channel Index: Range 0 - SPI Bus Count - 1
- VOID	Return

	OneWireReceiveByte
Receives a byte from the one wire bus a bit at a time
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	I2CSend
Transmit a byte using the I2C bus
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	DataOut
[[File:]] -	Return

	UARTSend
Send a byte via the UART module
- BYTE	Channel
Channel Index: Range 0 - UART Bus Count - 1
- BYTE	Data
Data Byte to send. Range: 0-255
- VOID	Return

	OneWireGetDeviceCount
Returns the number of devices found by the last ScanBus operation.
- BYTE	Channel
Channel Index: Range 0 - I2C Bus Count - 1
- BYTE	Return

	PWMSetPrescaler
Sets the prescaler for the PWM output
- BYTE	Channel
Range: 0 - 11
- BYTE	Prescaler
- BYTE	Period
- VOID	Return

	PWMEnable
Enable a PWM output
- BYTE	Channel
Range: 0-11
- VOID	Return

	ADCSampleArray10
Reads the voltage present on an Analog pin as an 10-bit value range 0-1023 Performs the selected number of samples with the selected time in microseconds in between samples and returns each sample in a single packet
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 32
- UINT	SampleDelay
Delay in us between each sample
- UINT	Samples
10-bit samples returned from the function
- VOID	Return

	ADCSampleAverage8
Reads the voltage present on an Analog pin as an 8-bit value range 0-255 Performs the selected number of samples with the selected time in microseconds in between samples
- BYTE	ADCChannel
Range: 0, 3-7
- BYTE	SampleCount
Range: 1- 100
- BYTE	SampleDelay
Delay in us between each sample
- BYTE	Return

	Initialise
Initialise the comms to the Arduino board ready for commands to be sent.
- VOID	Return

	PWMEnable
Allows pulse width modulated transistor outputs to be switched on or off. Bit 0 = Enable AB Bit 1 = A / Bit 2 = B Bit 3 = C / Bit 4 = D Bit 5 = Enable CD
- BYTE	EnableMask
Range 0-63 or 0b00000 to 0b111111
- VOID	Return

	Initialise
- VOID	Return

Property reference

	Properties
	ADC Channel
The ADC channel to which the thermistor circuit is connected. It is assumed that the thermistor is connected between the ADC pin and 0V, with a fixed resistor connected between the ADC pin and +V.
	ADC Bit Resolution
	Conversion speed
Clock setting to select how fast the ADC peripheral will perform an ADC conversion. The FRC setting is based on a RC time base and so will vary with temperature and pressure. Other settings are generally based on divisions of the master clock.
	Acquisition cycles
Number of micro seconds to wait for the ADC input to charge before starting the analogue sample.
	Wiring
Specifies the arrangement of the Thermistor and Fixed Resistor. Pull Down - Thermistor connected between ADC pin and GND, fixed resistor between ADC pin and VCC. Pull Up - Thermistor connected between ADC pin and VCC, fixed resistor between ADC pin and GND.
	Resistor Value
Value in Ohms of the pullup series resistor. i.e. The resistor is connected between the ADC pin and the positive supply rail.
	-25C Thermistor Value
Value in Ohms of the Thermistor at -25 deg C
	0C Thermistor Value
Value in Ohms of the Thermistor at 0 deg C
	25C Thermistor Value
Value in Ohms of the Thermistor at 25 deg C
	50C Thermistor Value
Value in Ohms of the Thermistor at 50 deg C
	75C Thermistor Value
Value in Ohms of the Thermistor at 75 deg C
	100C Thermistor Value
Value in Ohms of the Thermistor at 100 deg C
	125C Thermistor Value
Value in Ohms of the Thermistor at 125 deg C
	Connections
	Simulations
	Label
A text label to help you identify the component on the panel.
	Min. Temp.
Minimum termperature that can be set or displayed on the thermometer slider.
	Max. Temp.
Maximum termperature that can be set or displayed on the thermometer slider.
	Scale divisions
Number of numbered divisions shown on the thermometer scale.