Difference between revisions of "Component: Barometer (BMP180) (Environmental)"
From Flowcode Help
Jump to navigationJump to search| Line 16: | Line 16: | ||
==Detailed description== | ==Detailed description== | ||
| + | |||
| + | |||
| Line 24: | Line 26: | ||
==Examples== | ==Examples== | ||
| + | |||
| + | |||
| Line 41: | Line 45: | ||
|- | |- | ||
|- | |- | ||
| − | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:]] - | + | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:Fc9-f32-icon.png]] - FLOAT |
| width="90%" style="border-top: 2px solid #000;" | ''Return'' | | width="90%" style="border-top: 2px solid #000;" | ''Return'' | ||
|} | |} | ||
| Line 85: | Line 89: | ||
|- | |- | ||
|- | |- | ||
| − | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:]] - | + | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:Fc9-f32-icon.png]] - FLOAT |
| width="90%" style="border-top: 2px solid #000;" | ''Return'' | | width="90%" style="border-top: 2px solid #000;" | ''Return'' | ||
|} | |} | ||
| Line 98: | Line 102: | ||
|- | |- | ||
|- | |- | ||
| − | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:]] - | + | | width="10%" align="center" style="border-top: 2px solid #000;" | [[File:Fc9-f32-icon.png]] - FLOAT |
| width="90%" style="border-top: 2px solid #000;" | ''Return'' | | width="90%" style="border-top: 2px solid #000;" | ''Return'' | ||
|} | |} | ||
Revision as of 13:31, 17 November 2021
| Author | Matrix TSL |
| Version | 1.1 |
| Category | Environmental |
Contents
Barometer component
Barometric pressure sensor with a I2C bus interface. Pressure range 300 to 1100 hPa. Temperature range -40 to +85 °C.
Detailed description
No detailed description exists yet for this component
Examples
No additional examples
Downloadable macro reference
|
ReadPressureFloat |
| Reads the pressure as a floating point value in Bars. Calls the ReadPressureRaw function and then converts to a meaningful value. | |
 - FLOAT
|
Return |
|
|
Reset |
| Resets the device | |
 - VOID
|
Return |
|
|
I2C_Read_Register |
| Reads a byte value from a register on the device | |
 - BYTE
|
Address |
| - BYTE
|
Return |
|
|
ReadTemperatureFloat |
| Reads the temperature as a floating point value in °C. Resultion sets the return bit value and conversion time. Calls the ReadTemperatureRaw function and then converts to a meaningful value. | |
| - FLOAT
|
Return |
|
|
Altitude |
| Calculates the altitude based on difference between actual pressure and the pressure at the sea level P0=1013.25 hPa. | |
| - FLOAT
|
Return |
|
|
Forced_Read |
| - VOID
|
Return |
|
|
I2C_Write_Register |
| Writes a byte value to a register on the device | |
| - BYTE
|
Address |
| - BYTE
|
Value |
| - VOID
|
Return |
|
|
Initialise |
| Starts up the I2C bus and initialises the pressure sensor ready for use. Returns 1 for a sucessful startup. Returns 0 for a failed startup or no device detected. | |
| - BYTE
|
Return |
Property reference
|
Properties |
|
Slave Address |
|
|
Channel |
| Channel selection | |
|
SDA |
| Pin used for SDA (data signal) | |
|
|
SCL |
| Pin used for SCL (clock signal) | |
|
|
Baud Select |
| Baud rate option selector | |
|
Baud Rate |
| Baud rate to be used | |
|
Stop Delay |
| On older microcontroller devices there is a potential for the I2C hardware channel to lock up if there is not a 10ms delay between an I2C stop event and the next I2C start event. Most modern microcontrollers will not have a problem so this property can be disabled to speed up the I2C communications. | |
|
|
Compensation |
| Compensation formulas in double precision floating point or 32 bit fixed point | |
|
|
Humidity Oversampling |
|
|
Pressure Oversampling |
|
|
Temperature Oversampling |
|
|
Mode |
|
|
Standby Normal Mode (ms) |
|
|
Filter Coefficient |
|
|
Scope Traces |
| Selects if the scope traces are automatically generated or not | |
|
|
Console Data |
| Selects if the console data is automatically generated or not | |
|
|
API |
|
Connections |
|
|
Simulations |
|
|
Simulate Comms |
| Allows the simulation data to come from the panel GUI or relayed via an injector component. | |
