Component: K8055D (Third Party)
| Author | Matrix Ltd |
| Version | 2.3 |
| Category | Third Party |
K8055D component
Support for the Velleman K8055 USB input/output board. Allows Flowcode to communicate with up to four K8055 boards, or to simulate them with interactive on-screen controls. All digital and analog I/O functions are supported.
Component Source Code
Please click here to download the component source project: FC_Comp_Source_K8055D.fcsx
Please click here to view the component source code (Beta): FC_Comp_Source_K8055D.fcsx
Detailed description
No detailed description exists yet for this component
Examples
No additional examples
Macro reference
GetCount
|
GetCount |
| Read the value of the chosen counter for the currently selected board. | |
 - INT
|
Counter |
| The counter to read (1 or 2) | |
 - UINT
|
Return |
GetAnalogIn
|
|
GetAnalogIn |
| Read analog input 1 or 2 | |
| - INT
|
Input |
| Which input to read (1 ro 2) | |
| - INT
|
Return |
SetAnalogOut
|
|
SetAnalogOut |
| Sets the chosen analog output to the given value (0-255) | |
 - BYTE
|
Output |
| Which output to set the value for (1 ro 2) | |
| - BYTE
|
Value |
| Value to set (0-255) | |
 - VOID
|
Return |
SetDigitalOut
|
|
SetDigitalOut |
| Sets the state of the output given by the output index (1 to 8) | |
| - BYTE
|
Out |
| Number of the output to set the value for | |
 - BOOL
|
Value |
| - VOID
|
Return |
GetDigitalByte
|
|
GetDigitalByte |
| Read all five inputs at once, returning them as a bit pattern in a byte. The upper three bits will always be zero. | |
| - INT
|
Return |
ResetCount
|
|
ResetCount |
| Resets the chosen counter of the currently selected board. | |
| - INT
|
Counter |
| Which counter to reset (1 or 2) | |
| - VOID
|
Return |
GetDevices
|
|
GetDevices |
| Returns a value representing the available devices. Device is a binary value where bit(N) set = device at address (N) is connected. | |
| - INT
|
Return |
Select
|
|
Select |
| Selects the board address to send to and receive data from. Echos the address if the selection is valid. Returns -1 if there is no device available at that address. | |
| - INT
|
Address |
| The address off the board to be selected (0...3). | |
| - INT
|
Return |
SetDigitalByte
|
|
SetDigitalByte |
| Sets all eight digital outputs according to the individual bits of the Value parameter. | |
| - BYTE
|
Value |
| Value to send to the selected board. | |
| - VOID
|
Return |
GetDigitalIn
|
|
GetDigitalIn |
| Read the individual input at the given index (1..5) | |
| - INT
|
Input |
| Which input to read (1 to 5) | |
| - INT
|
Return |
SetCountDebounce
|
|
SetCountDebounce |
| Set the amount of time allowed for switches to settle before being counted as a new event to count. | |
| - INT
|
Counter |
| Which counter to make a setting for (1 or 2) | |
| - INT
|
DebounceTime |
| Settling time for switch debouncing in milliseconds | |
| - VOID
|
Return |
Property reference
|
Properties |
|
Simulation |
|
Addr 0 |
| Use software simulation to emulate a board connected at address 0. | |
|
|
Addr 1 |
| Use software simulation to emulate a board connected at address 1. | |
|
|
Addr 2 |
| Use software simulation to emulate a board connected at address 2. | |
|
|
Addr 3 |
| Use software simulation to emulate a board connected at address 3. | |
|
|
Hardware |
|
Scan |
| Request a scan of the currently connected hardware to detect what Velleman boards are connected and at what addresses. Where hardware is not detected at an addess, a System Panel simulation will be used instead where one has been requested in the properties. | |