Component: DAC Quad (MCP4728) (MCP4728) (Analog Output)

Author	Matrix TSL
Version	1.0
Category	Analog Output

DAC Quad (MCP4728) component

Component to drive a quad digital to analogue converter (DAC) IC from Microchip via an I2C interface. Compatible with MCP4728 (12-Bit) devices.

Detailed description

No detailed description exists yet for this component

Examples

No additional examples

Downloadable macro reference

	SetOutput
Sets the output voltage of the DAC 12-Bit: Range 0-4095
- BYTE	Channel
Range: 0-3 / 0=DAC Channel 0 / 1=DAC Channel 1 ...
- UINT	DAC_Value
The value to output to the DAC
- VOID	Return

	ControlPins
Allows Shutdown (SHDN) and Latch (LDAC) pins to be controlled directly if enabled.
- BOOL	Latch
0 = Data output driven from DAC register, 1 = Data output locked
- VOID	Return

	SetInitialEEOutput
Stores a DAC value into EE memory to be used on power up.
- BYTE	Channel
Range: 0-3 / 0=DAC Channel 0 / 1=DAC Channel 1 ...
- UINT	DAC_Value
The value to output to the DAC
- VOID	Return

	Disable
Disables the DAC output.
- BYTE	Channel
Range: 0-3 / 0=DAC Channel 0 / 1=DAC Channel 1 ...
- VOID	Return

	Enable
Enables the DAC Output.
- BYTE	Channel
Range: 0-3 / 0=DAC Channel 0 / 1=DAC Channel 1 ...
- VOID	Return

	SetDeviceAddress
Writes a new device address into EE memory. The use LDAC pin component property must be set to true and the LDAC pin should be unique for every MCP4728 device connected to the I2C bus.
- BYTE	OldAddress
Range: 0-7
- BYTE	NewAddress
Range: 0-7
- VOID	Return

	Initialise
Configures the SPI peripheral ready for communications and initialises the internal variables. DAC needs to be enabled before any output voltage can be generated.
- VOID	Return

Property reference

	Properties
	Pull Down Option
	VREF Option
	Gain Option
Selects the maximum reference value for the DAC
	Vref Voltage
Reference Voltage, Used to calculate the Voltage resolution.
	Steps
Number of discrete output states available from the DAC.
	Control Bits
Number of digital control bits
	Resolution
Maximum output resolution based on number of control bits.
	Voltage Resolution
Specifies the Resolution per digital bit in terms of Voltage.
	Device Address
	Channel
Channel selection
	SDA
Pin used for SDA (data signal)
	SCL
Pin used for SCL (clock signal)
	Baud Select
Baud rate option selector
	Baud Rate
Baud rate to be used
	Stop Delay
On older microcontroller devices there is a potential for the I2C hardware channel to lock up if there is not a 10ms delay between an I2C stop event and the next I2C start event. Most modern microcontrollers will not have a problem so this property can be disabled to speed up the I2C communications.
	Use LDAC Pin
Allows the LDAC pin to be driven from an output pin on the microcontroller. If not used then tie the LDAC pin to GND to allow the DAC to function.
	Connections
	Simulations
	Simulation Comms
	DAC Output Scope Traces
Selects if the scope traces are automatically generated or not
	Scope Traces
Selects if the component pin connections are automatically generated on the data recorder window or not. Yes: Automatically add the component pins to a group on the data recorder which will reflect the sim data during simultion. No: Do not show the pin signals on the data recorder window.
	Console Data
Selects if the console data is automatically generated or not
	API
Specifies the injector component on the panel to interact with to provide comms simulation.