Search found 1065 matches
- Fri May 10, 2024 7:52 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi Work not holiday and I didn't know about the pencil museum. 2B or not 2B I guess? Fueled by Raven Red I discovered if I add in the IME component before I add in the Network Comms component, then no matter how many times I try the NC is a no show. However if I add the WLAN ESP32, then the Network ...
- Fri May 10, 2024 5:47 am
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi I've been down South (or up North depending on viewpoint) for a few days this week in the Lake District. I've not been there since childhood and I'd forgotten how beautiful it is. Day trips, so long days and I'm just heading off there again today. No hardship with the scenery I pass through :) As...
- Thu May 09, 2024 9:37 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi
Sorry, a little busy this week and I've not had time to post my TS mqtt file. If using the "free" version of TS then you are limited to how many posts you can make and also frequency too. I could only reliably post every 12 - 15 seconds or so.
Regards
Sorry, a little busy this week and I've not had time to post my TS mqtt file. If using the "free" version of TS then you are limited to how many posts you can make and also frequency too. I could only reliably post every 12 - 15 seconds or so.
Regards
- Tue May 07, 2024 10:37 pm
- Forum: Bug Reports
- Topic: SR04 Ultrasonic Sensor
- Replies: 6
- Views: 119
Re: SR04 Ultrasonic Sensor
Hi "Me" moving around the PC to "capture" may have been in the picture so to speak when triggering / grabbing a pulse trace, but when only reading the display I'm not really near it. The sensor loops at one second intervals so I see when I or anything else is detected. If me, at 140 / 144 (140 / 4 o...
- Tue May 07, 2024 9:01 pm
- Forum: Bug Reports
- Topic: SR04 Ultrasonic Sensor
- Replies: 6
- Views: 119
Re: SR04 Ultrasonic Sensor
Hi Yes I did expect the pulses to diverge with distance but it did not appear to affect anything at all in my test set up, as it was not always in the same position relative to surrounding, but did always have fun above 140. Just to be clear at 140cm all good, at 141cm it reads 1cm and increases acc...
- Mon May 06, 2024 9:36 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi
Simulating my mqtt chart updated TS however I think it is corrupted somehow as it displays variables not used in the project at all. I need to look at it in daylight before posting.
Regards
Simulating my mqtt chart updated TS however I think it is corrupted somehow as it displays variables not used in the project at all. I need to look at it in daylight before posting.
Regards
- Mon May 06, 2024 6:46 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi As you might have guessed, the Talisker did an astounding job and I highly recommend it (although Highland Park may be more geographically suited :D ). Today was more theory than practical. I thought about doing stuff but the chances of that happening were practically zero.... How did you get on ...
- Mon May 06, 2024 3:24 pm
- Forum: Bug Reports
- Topic: SR04 Ultrasonic Sensor
- Replies: 6
- Views: 119
Re: SR04 Ultrasonic Sensor
Hi Martin Sorry, only tried timer didn't check non-timer . I will try next time I'm in the evil lab. I also tried just the example file but it too does the same (just in case I'd missassigned a variable or such). Watching the analyser, the module even detects the angle being adjusted slightly. It's ...
- Sun May 05, 2024 10:01 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Thought I'd save some for tomorrow. Now on Talisker which never disappoints
- Sun May 05, 2024 9:13 pm
- Forum: General
- Topic: IOT_Made_Easy - or not?
- Replies: 23
- Views: 333
Re: IOT_Made_Easy - or not?
Hi
Not even after multiple. I knew about second clicking and to add "target" prior, but can't get it to work. I can get for example mqtt to link though so it seems limited to IME (or maybe .39 as I'm not near a .38 to check)
Regards
Not even after multiple. I knew about second clicking and to add "target" prior, but can't get it to work. I can get for example mqtt to link though so it seems limited to IME (or maybe .39 as I'm not near a .38 to check)
Regards