Components that cannot be used

[monie]

For Flowcode
Regarding Flowcode v10
Here below are components marked in red that I cannot be allowed to use

Licening and account.jpg (37.73 KiB) Viewed 4806 times

Components that do not work can be seen below

Skærmbillede 2023-05-24 072947.jpg (54.08 KiB) Viewed 4806 times

Skærmbillede 2023-05-24 073135.jpg (54.37 KiB) Viewed 4806 times

And 2x Licensing and account I cannot upload to you

Can you help me with these components. So I can get to use them...

Best Regards
Monie

[medelec35]

Hi Monie.
You should still be able to compile to them, as there is a visual bug that shows some licensed target devices as not licenced.

For example:

ECIO40.png (24.88 KiB) Viewed 4798 times

When I compile to the ECIO40 hardware:

Code: Select all

Launching the compiler...
C:\Program Files (x86)\Flowcode\Common\Compilers\picv2\bin\xc8.exe  --chip=18F4455 "ECIO40 prog test.c" --MSGDISABLE=359,1273,1388 --CODEOFFSET=800h --ROM=default,-0-7FF
C:\Program Files (x86)\Flowcode\Common\Compilers\picv2\pic\bin\picc18 --chip=18F4455 ECIO40 prog test.c --MSGDISABLE=359,1273,1388 --CODEOFFSET=800h --ROM=default,-0-7FF
Microchip MPLAB XC8 C Compiler V2.10
Build date: Jul 30 2019
Part Support Version: 2.10
Copyright (C) 2019 Microchip Technology Inc.
Employing 18F4455 errata work-arounds:
 * Corrupted fast interrupt shadow registers
 * No stopping on H/W breakpoints after NOP2

Memory Summary:
    Program space        used    72h (   114) of  5800h bytes   (  0.5%)
    Data space           used     7h (     7) of   800h bytes   (  0.3%)
    Configuration bits   used     7h (     7) of     7h words   (100.0%)
    EEPROM space         used     0h (     0) of   100h bytes   (  0.0%)
    ID Location space    used     0h (     0) of     8h bytes   (  0.0%)
    Data stack space     used     0h (     0) of   7A0h bytes   (  0.0%)


Using <E-Blocks> inbuilt settings for linker
Launching the linker/assembler...
C:\Program Files (x86)\Flowcode v10\tools\DoNothing\DoNothing.exe  

Using FCD settings for programmer
Launching the programmer...
C:\Program Files (x86)\Flowcode v10\tools\mLoader\mLoader.exe  -ecio40 "ECIO40 prog test.hex"
. . . .

Loading file...
File loaded from...
=> ECIO40 prog test.hex
File sending...
File sent!

If you compile and it does not say "You don't have a valid licence" then there is a different issue.
I have also compiled to TTGO OK.

[monie]

Hi Martin
I have a valid Professional license for 1 user:-)

[Steve-Matrix]

monie - those targets with the red exclamation mark should compile ok for you. You can safely ignore the red exclamation marks if you have a licence for the associated chip-pack.

Have you tried creating a simple project with one? Are you receiving any errors when compiling to these targets?

[monie]

Hi Steve-Matrix

Tried to test ECIO 40P but without success.
At "Program Port:" here I don't have the option to select anything?
See attached JPG-file

Test Af ECIO-40 Enhed.jpg (47.39 KiB) Viewed 4787 times

Monie

[medelec35]

Hi Monie.
That is correct, the programmer port remains blank.
Before programming the ECIO, make sure the ECIO LED is solidly lit.
If the LED flashes all the time, then the drivers have not been installed.
They are available here (40 pin)
or
here (28pin)

To program the ECIO40.
Select Build >Compile to target as normal.
You should get a popup stating No device detected etc.
At that point, you press the button on the ECIO to program it.
After pressing the button the ECIO then establishes a connection to the PC, so you will hear the driver-detected sound, and the LED will flash indicating it's being programmed.
After programming is completed the LED will stop flashing and remain on in a steady state.

[monie]

Hi Steve-Matrix

Thanks for your nice description..

When I try to do as you describe I Get the message: See below!

PIC compiler toolchains

PIC compiler toolchains.jpg (11.75 KiB) Viewed 4767 times

What is the reason?

What should I do. Do you have a suggestion?


Monie

[medelec35]

Hi Monie, Your welcome.
Have you downloaded and installed the 8bit PIC toolchain from here?
That message is stated it's not installed.

[monie]

Hi Steve-Matrix

I cannot compile the file for ECIO40P...?

Choos a Targe ECIO40P.jpg (48.88 KiB) Viewed 4712 times

Please see "Compiler messages.pdf" below!

Compiler messages.pdf

(43.7 KiB) Downloaded 439 times

Hope you can help me so I can use ECIO40 with Flowcode v10....

Monie

[medelec35]

Hi Monie.
Does the ECIO have a solid or Flashing LED when connected via USB to your PC?